PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA)

‘Windows’ keyboard assembly (Quartz Gray, 105 key) – Has attached 1.8M cable with 6-pin (Violet) mini DIN connector (Option ABF, European-French) – Replacement for the C1405B, C1405C, and D4950B Keyboards

Serial management ribbon cable – 6.8cm (2.7in) cable with a 10-pin (F) connector and a DB-9 (M) connector attached to rear panel filler panel – The cable is marked ‘Remote Assist Cable’ and the filler panel is marked ‘Management Port’

Ribbon cable – 3-pin (F) connector to 3-pin (F) connector – 40cm (15.8in) long – I2C bus cable assembly (E) – From system backplane board to hot-swap backplane board

Floppy drive ribbon cable marked ‘Floppy disk’ – 34-pin (F) connector marked ‘to system board’ to 34-pin (F) connector marked ‘to 3.5 inch flexible disk drive’ – 50.2cm (19.8in) long – Cable C

IDE CD-ROM drive ribbon cable marked ‘IDE cable D6’ – 40-pin (F) connector marked ‘To system board’ to a 40-pin (F) connector marked ‘To IDE CD-ROM’ – 17.1cm (6.8in) long – Cable B – From system backplane board to IDE devices

Terminated 90 ohm SCSI ribbon cable kit (C42) with 68-pin (M) connectors – A cable clamp, a connector marked ‘To system board’, four connectors marked ‘To Unterminated SCSI Device’, and a 50-pin (F) to 68-pin (F) adapter – 86.1cm (33.9in) long – Wide SCSI

SCSI ribbon cable kit (C52) – A 68-pin (F) to 50-pin (F) adapter and a cable marked ‘Int/Ext SCSI cable C52-90 ohm’ with 68-pin (M) connectors marked ‘to Sys Bd’, ‘to unterminated SCSI device’, and ‘to Mass Storage Device’ – 70.4cm (27.7in) long – Wide SC

SCSI cable kit with termination (C82) – Self-adhesive cable clamp and a cable marked ‘Int SCSI cable C82-90 ohm’ – Three 68-pin (M) connectors, one marked ‘to system board’, the others marked ‘to Unterminated SCSI device’ – 65.3cm (25.7in) long – Wide SCS

Fast Wide SCSI ribbon cable (C23) – Cable marked ‘External SCSI port cable C23-90 ohm’ – 68-pin (M) connector marked ‘To system board’ to high density 68-pin (F) connector with latch clips for the rear panel – 51.8cm (20.4in) long – From one of the proces

Fast Wide SCSI ribbon cable (C23) – Cable marked ‘External SCSI port cable C23-90 ohm’ – 68-pin (M) connector marked ‘To system board’ to high density 68-pin (F) connector with latch clips for the rear panel – 51.8cm (20.4in) long – From one of the proces

‘Hot swap’ bezel assembly – Frame around 3 ‘hot swap’ drives

Front bezel assembly

System fan – Mounts on the rear of the cabinet

Processor fan and bracket assembly – (P/O some accessory kits) – If Installed, it is mounted on the right side of the processor bracket

8-port Console Switch – Connect up to eight computers to a single monitor, keyboard, and mouse – Includes rack mounting hardware – Must order connecting cables separately

Adapter – 68-pin high density (F) to 50-pin (F) – Used to connect 68-pin (M) ribbon cable to 50-pin (M) Narrow SCSI device – (C5710A)

Adapter – 68-pin high density female to 50-pin female – Used to connect 68-pin male ribbon cable to 50-pin male Narrow SCSI device

Adapter – 68-pin high density female to 50-pin female – Used to connect 68-pin male ribbon cable to 50-pin male Narrow SCSI device

Heat sink clip – Heat sink clip for Pentium II module – Two used

Top cover assembly

5.25-inch filler panel (Quartz Gray) – For empty 5.25-inch drive bays above the Hot-Swap drive bay

Hot Swap drive filler panel (Flint Gray) – For empty Hot-Swap drive slots

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive

NetServer Storage System/6 – External cabinet which can hold up to two half-height non-hot-swap Fast SCSI-2 drives and up to six hot-swap drive modules – Includes cabinet with 6 bays, 2 common tray shelves, dual SCSI backplane, and redundant power s

NetServer Storage System/12 – External cabinet which can hold eight half height, or 12 low profile Ultra2 SCSI drives – Includes one Rack Storage 12 Ultra2 SCSI card

NetServer Storage System/12 – External cabinet which can hold eight half height, or 12 low profile Ultra2 SCSI drives – Includes one Rack Storage 12 Ultra160 SCSI card

24GB internal SureStore DAT 24i Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive (Flint)

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

10/20GB SureStore T20e Single-Ended Narrow SCSI-2 external Travan TR-5 tape drive – Includes power supply, cables, tape, and software

6×12/24GB SureStore DAT 24×6i Single-Ended Narrow SCSI-2 internal autoloader DDS-3 (DAT) tape drive

1.44MB, 3.5-inch floppy drive (Flint Gray bezel)

2.1GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

4.2GB hot-swap SCSI-2 hard drive module (Flint Gray)

4.2GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

9.1GB hot-swap Ultra SCSI-2 hard drive module (Quartz Gray)

9.1GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

IDE CD-ROM drive – 48X CD-ROM read (Mitsumi CRMC-FX4820T) – Has front panel headphone jack and volume control

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

4.2GB Ultra Wide SCSI hard drive – 7,200 RPM

4.2GB Ultra Wide SCSI hard drive – 7,200 RPM

4.2GB Wide Single-Ended SCSI hard drive – 7,200 RPM

4.2GB Wide Single-Ended SCSI hard drive – 7,200 RPM

9.1GB Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB Ultra Wide SCSI hard drive module – 7,200 RPM

18.2GB hot-swap Ultra Wide SCSI hard drive module – 7,200 RPM

18.2GB hot-swap Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB hot-swap Ultra SCSI hard drive module – 10,000 RPM

9.1GB Ultra Wide SCSI hard drive module – 10,000 RPM

9.1GB Ultra Wide SCSI hard drive – 10,000 RPM, 3.5-inch form factor

18.2GB Wide Single-Ended SCSI hard drive – 7,200 RPM

18.2GB Ultra Wide SCSI hard drive – 7,200 RPM, 3.5-inch form factor

18.2GB Ultra3 Wide SCSI LVD hard drive module – 10,000 RPM, 3.5-inch form factor, 1.0-inch high (Seagate ST318404LW)

9GB Ultra3 SCSI hard drive module – 10000 RPM, 3.5in form factor, low profile

8GB SureStore DAT8i DDS-2 tape drive – (C1528K)

10/20GB SureStore T20i Single-Ended Narrow SCSI-2 internal Travan TR-5 tape drive – Includes tape and software

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

9.1GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM, SCA 80-pin connector

9GB Ultra3 SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high

18GB Ultra3 SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high – Comes mounted on a drive tray

512kB, 50ns EDO VRAM video memory IC – Plugs into sockets on system processor board – (Two or four required, 1MB kit is D4219A) – Installing two IC’s will upgrade to 2MB total of video memory

1MB video memory upgrade kit – Includes two 512kB, 50nS EDO video memory IC’S

128MB, 100MHz registered ECC SDRAM DIMM memory module – (D6098A) for HP LC3 NetServer

256MB, 100MHz registered ECC SDRAM DIMM memory module – (D6099A) for HP LC3

64MB SIMM memory module for NetRAID 3Si disk array controller – (D7132A) for HP LC3

64MB, 100MHz registered ECC SDRAM DIMM memory module – (D6097A) for HP LC3 NetServer

HP NetServer Terminator board – Used in secondary processor socket for a system with only one processor

HP LC3 System Processor Board – For up to two PII/PIII Processors – Mounts Vertically in the Center of the Chassis

HP LC3 Hot Swap’ Backplane Board – for Three ‘Hot Swap’ Drives – Mounts in the the Rear of the ‘Hot Swap’ Drive Cage

HP LC3 NetServer System Backplane Board – Large Horizontal Board in Center of the NetServer – Has Sockets for Add-in ISA or PCI Boards

HP LC3 NetServer System Backplane Board – Large Horizontal Board in Center of the NetServer – Has Sockets for Add-in ISA or PCI Boards

NetRAID-1si – One-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

NetRAID 3-Channel Disk Array Controller – PCI Board With 3 Internal 68 Pin and 2 External 68 Pin High Density Ultra Wide SCSI Connectors (D4943A)

NetRAID 3-Channel disk array controller – PCI board with 3 internal 68 pin and 2 external 68 pin high density Ultra wide SCSI connectors, manual, and NetServer Navigator CD-ROM

NetRAID-1 One-Channel Disk Array Controller – PCI Board With One Internal 68 Pin High Density and One External 68 Pin High Density Ultra Wide SCSI Connector (D4992A)

NetRAID-1 one-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

LAN Adapter – PCI 10/100TX LAN Board for NetServer (D5013A)

NetRAID-3Si Three-Channel Disk Array Controller – PCI Board With Three Internal 68 Pin High Density and Three External 68 Pin High Density Ultra Wide SCSI Connectors (D5955A)

NetRAID-3si three-channel disk array controller – PCI board with three internal 68 pin high density and three external 68 pin high density Ultra wide SCSI connectors

Ultra2 SCSI host adapter

Ultra3 SCSI host adapter

Ultra3 SCSI host adapter

Ultra3 SCSI host adapter

TopTools remote control card with battery (Version 1) – Allows emergency remote access using LAN or modem

PCI 32-BIT LAN interface board – Has RJ-45 connector – Supports both EtherTwist (10Base-T) and 100VG/802.12 – PCI 32-Bit LAN Interface Board – has RJ-45 Connector – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585B, 1/6 of J3009B, 1/24 of J3010B)

TopTools remote control card with battery (Version 2.0) – Allows emergency remote access using LAN or modem

Gigabit LAN adapter – PCI-X 10/100/1000TX 3Com LAN card – (3Com 3C996-T)

Wide SCSI Host Adapter Board (D5025A) – Installed in PCI Socket on System Backplane Board

Wide SCSI Host Adapter Board – Installed in PCI Socket on System Backplane Board – May Need Cables D5968A and D6001A

32-bit PCI LAN interface board – RJ-45 connectors – Supports both EtherTwist 10Base-T and 100VG/802.12 – (J2585B, part of J3009B, part of of J3010B)

Power supply assembly – 350 watts – NOTE: The fan inside the power supply is not available separately

Intel Pentium II processor – 350MHz (Deschutes, 100MHz front side bus, 512KB Level-2 cache, Slot 1) – for HP LC3 PII/350

Intel Pentium II processor upgrade – Includes one 350MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor for HP LC3 PII/350 NetServer

Intel Pentium II processor – 400MHz (Deschutes, 100MHz front side bus, 512KB Level-2 cache, SECC-2, Slot 1) – Includes heat sink -for HP LC3 PII/400

Intel Pentium II processor upgrade – Includes one 400MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor

Intel Pentium II processor – 450MHz (Deschutes, 100MHz front side bus, 512KB Level-2 cache, Slot 1, ECC) – Includes heat sink – for HP LC3 PII/450

Intel Pentium II processor upgrade – Includes one 450MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor

Intel Pentium III processor – 500MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache, Slot 1) – Includes heat sink – for HP LC3 PIII/500

Intel Pentium III processor – 550MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache, Slot 1) – Includes heat sink – for HP LC3 PIII/550

Intel Pentium III processor upgrade – Includes one 550MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache) processor

Intel Pentium III processor upgrade – Includes one 500MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache, ECC) processor