Cable assembly – DB-9 (M) connector to DB-9 (F)connector – 2.9m (9.6ft) long – From multifunction I/O board to ADP I MUX panel

Single-Ended SCSI ribbon cable – 50-pin (F) connector to SCSI controller and four 50-pin (F) connectors for drives – 78.4cm (30.9in) long – To the hard drives in the peripheral drive bay drawer

Y’ cable assembly – 78-pin (M) connector with thumbscrews to two 3.9m (12.9ft) long cables terminated with low density 50-pin (M) connectors with thumbscrews – From multifunction I/O board to two DDP panels – (part of J2092A or J2093A)

Cable assembly – 78-pin (M) connector with thumbscrews to DB-9 (F) connector – 3.9m (12.9ft) long – From multifunction I/O to ADP II MUX panel

SCSI interface cable – 50-pin high density (M) thumbscrew to 50-pin low density (M) bail lock – 1.0m (3.3ft) long

Single-Ended SCSI ribbon cable – 50-pin (M) connector to 50-pin (F) connector – A 10.5cm (4.1in) cable is folded to a final length of 4.0cm (1.6in) – To the removable media drives in the peripheral drive bay drawer

MUX ‘Y’ cable – MUX ‘Y’ cable – From I/O to two ADP II panels

Chassis assembly – Internal metal structure of the computer

Rear bezel (metal) – Helps to retain boards in computer

Front bezel – Plastic front panel with air vent louvers – For desk side configuration

Front bezel – Plastic front panel with air vent louvers – For rack mounted configuration

DC power switch – Includes cable to power control module – Mounts in the upper left corner of the chassis

Right backplane retainer clip – Right retainer clip – Holds backplane on alignment tabs

Left backplane retainer clip – Left retainer clip – Holds backplane on alignment tabs

Cover plate – For empty single high HP-PB I/O board slots (Includes the two captive screws)

Cover plate – For empty double high HP-PB I/O board slots (Includes the two captive screws)

Right side panel – For standard or expanded chassis

Rear panel – Mounts to the rear of the chassis

19-inch direct rackable distribution panel (DDP-RJ45, Tyco 144801-1) – External panel with sixteen RS-232C or RS-423A direct connect ports (Standard)

Half-height filler panel – Covers unused multimedia drive bay slots – Mounts above the front display panel

Left side panel assembly – Includes L-shaped top cover

5GB, 8mm Single-Ended SCSI (DAT) tape drive

4.0GB Single-Ended SCSI DDS-2 tape (DAT) drive – 5.25-inch form factor

2.0GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor, half height

Single-Ended SCSI-2 CD-ROM drive – 4X CD-ROM read

1.44MB 3.5-inch Single-Ended SCSI-2 Floppy drive

1.2GB Single-Ended SCSI QIC tape drive

535MB Single-Ended SCSI-2 hard drive – 3.5-inch form factor, half height

1.0GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor, half height

32MB ECC SIMM memory module for HP9000 E55

8MB ECC SIMM memory module for HP9000 E55

16MB ECC memory upgrade kit – Includes two 8MB SIMM modules

64MB ECC memory upgrade kit – Includes two 32MB SIMM modules

HP9000 E55 Backplane Board (with 4 I/O Slots) – Large Vertical Board Mounted in the Middle of the Chassis

HP9000 E55 HP-IB interface board – HP-IB Interface Board – for the HP-PB I/O Board Slot

HP9000 E55 Precision Bus Adapter(L-Shaped) – Adapts CIO Bd to Backplane

HP9000 E55 Multifunction I/O Board – Includes SCSI/Parallel Port, Plus Connector to the MUX (MDP) or Direct (DDP) Distribution Panels – Plug into Rear Center of the Computer

HP9000 E55 Backplane Board (with 2 I/O Slots) – Large Vertical Board Mounted in the Middle of the Chassis

HP9000 E55 96MHz System Processor Board – Plugs into Slot to the Right of the Multifunction I/O Board

16 Channel RS-232C Direct Connect MUX Board (with RJ-45 Connectors) – for the HP-PB I/O Board Slot

Fiber distributed data interface (FDDI) board – For the HP-PB I/O board slot

LAN Link (EtherNet or IEEE 802.3) Interface Board – for the HP-PB I/O Board Slot (P/O J2146A)

Single-ended SCSI interface host adapter board kit – For the HP-PB I/O board slot – Includes 1m (3.3ft) SCSI cable and terminator

HP-IB interface board – For the HP-PB I/O board slot

Single Ended SCSI-2/Centronics Host Adapter Board – for the HP-PB I/O Board Slot (P/O 28642A or 28655A)

Single-ended SCSI-2 and Centronics host adapter board – Includes a 1.0m (3.3ft) SCSI cable – For the HP-PB I/O board slot

X.25 Network Link Interface Board (Can be RS-232 Direct Connect or V.35 Depending on Option Selected) – for the HP-PB I/O Board Slot

CIO HP-IB interface board – CIO HP-IB Interface Board

CIO HP-FL disk interface – CIO HP-FL Disk Interface (27111A or 27115A) – Requires PBA

10/100Base-T LAN Adapter Interface Board – for the HP-PB I/O Board Slot (Auto Senses Between 10Mbps and 100Mbps)

Token ring interface board – For the HP-PB I/O board slot

Token ring interface board – For the HP-PB I/O board slot

Power supply kit with fan, plug, and power control module