PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA)

Ribbon cable with two self adhesive cable clamps and installation instructions – 8-pin (F) connector marked ‘NetServer’ to 8-pin (F) connector marked ‘Remote Assistant’ – 1.0m (39in) cable folded to be 63.5cm (25in) long – From Remote Assistant board to c

Ribbon cable with two self adhesive cable clamps and installation instructions – 8-pin (F) connector marked ‘NetServer’ to 8-pin (F) connector marked ‘Remote Assistant’ – 1.0m (39in) cable folded to be 63.5cm (25in) long – From Remote Assistant board to c

Ribbon cable assembly – 3-pin (F) connector to 3-pin (F) connector – 30cm (11.8in) long – I2C bus cable assembly – From hot-swap backplane boards to system (mother) board (two used)

Fast Wide SCSI ribbon cable – Cable is marked ‘Internal SCSI cable C22-90 ohm’ – Has one 68-pin (M) connector marked ‘To motherboard or PCI board’ and one 68-pin (M) connector marked ‘To SCSI mass storage device’ – 76.7cm (30.2in) long – Cable C22 – From

SCSI ribbon cable (C14) – Fast Wide (Ultra) cable marked ‘Int. SCSI bridge cable C14-90 ohm’ – 68-pin (M) connector marked ‘Top’ to 68-pin (M) connector marked ‘Bottom’ – 23.6cm (9.3in) long – Between the two hot-swap backplane boards (configuration depen

Fast Wide SCSI ribbon cable (C23) – Cable marked ‘External SCSI port cable C23-90 ohm’ – 68-pin (M) connector marked ‘To system board’ to high density 68-pin (F) connector with latch clips for the rear panel – 51.8cm (20.4in) long – From one of the proces

Ribbon cable for one IDE drive – 40-pin (F) connector to 40-pin (F) connector – 51cm (20in) long

Floppy drive ribbon cable – 34-pin (F) connector marked ‘to system board’ to a 34-pin (F) old-style edge connector and a 34-pin (F) new-style connector marked ‘to 3.5 inch flexible disk drive’ – 61.9cm (24.4in) long

Cable assembly – 24-pin (F) connector to four 6-pin (F) connectors marked ‘P1’, ‘P2’, ‘P3’, and ‘P4’ – Each cable assembly is 20cm (7.9in) long – Power supply cable for system board

Power supply cable assembly – 18-pin (F) connector marked ‘BP1’ to both a 12.1cm (4.8in) cable with a 3-pin (F) connector marked ‘P27’ and a 21.6cm (8.5in) cable with an 18-pin (F) connector marked ‘P16’ – Power supply cable for system board

Power supply cable assembly – 18-pin (F) connector marked ‘BP1’ to five cable bundles with an unmarked 4-pin (F) connector and 4-pin (F) connectors marked ‘P16’, ‘P17’, ‘P18’, ‘P19’, ‘P20’, ‘P21’, ‘P22’, and ‘P23’ – The longest cable is 38cm (15 inc – For

Fast Narrow SCSI-2 90 ohm ribbon cable with termination (C21) – Has a 50-pin (F) connector marked ‘To array back plane’ and two 50-pin (F) connector marked ‘To unterminated SCSI device’ – 47cm (18.5in) long – From CD-ROM drive to hot-swap backplane board

SCSI cable kit – Used to reconfigure the mass storage interfaces – Kit includes: hot swap backplane cable (C14), Fast/Wide port cable (C22), and 50-pin to 68-pin adapter (A)

Power supply cable assembly – 18-pin (F) connector marked ‘BP1’ to five cable bundles with an unmarked 4-pin (F) connector and 4-pin (F) connectors marked ‘P16’, ‘P17’, ‘P18’, ‘P19’, ‘P20’, ‘P21’, ‘P22’, and ‘P23’ – The longest cable is 38cm (15 inc – For

Bezel assembly – Has cut outs for switches and LED activity lights – Plastic cover over the control panel PC board

‘Hot swap’ bezel assembly (Flint Gray) – Frame around six ‘hot swap’ drives – Includes the lock

Hard drive tray bezel (Flint Gray) – For 3.5-inch hard drives

Fan assembly – With housing – Mounts to the rear panel in the upper slot (when second power supply has not been added)

Tubeaxial fan – Mounts to the front panel (Two used)

8-port Console Switch (Parchment White) – Connect up to eight computers to a single monitor, keyboard, and mouse – Desktop or rack mountable

4-port Console Switch – Connect up to four computers to a single monitor, keyboard, and mouse – Includes rack mounting hardware – Must order connecting cables separately

8-port Console Switch – Connect up to eight computers to a single monitor, keyboard, and mouse – Includes rack mounting hardware – Must order connecting cables separately

4-port Console Switch (Quartz Gray) – Connect up to four computers to a single monitor, keyboard, and mouse – Includes hardware, user manual, and power cable

8-port Console Switch (Quartz Gray) – Connect up to eight computers to a single monitor, keyboard, and mouse – Includes hardware, user manual, and power cable

SCSI adapter (68-pin (F) to 50-pin (M)) – Used in some configurations for the CD-ROM drive and/or another Single-Ended SCSI drive (Narrow 8-bit to Fast Wide 16-bit)

Heat sink retainer clip – Retainer clip – Holds the heat sink on the Processor IC

Chassis cover – Includes front, top and both sides

Locking cover (Flint Gray) – Attaches to the front of the ‘Hot Swap’ drive trays

5.25-inch filler panel (Quartz Gray) – For empty 5.25-inch drive bays above the Hot-Swap drive bay

Hot Swap drive filler panel (Flint Gray) – For empty Hot-Swap drive slots

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

2 button PS/2 serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-din connector

NetServer Storage System/6 – External cabinet which can hold up to two half-height non-hot-swap Fast SCSI-2 drives and up to six hot-swap drive modules – Includes cabinet with 6 bays, 2 common tray shelves, dual SCSI backplane, and redundant power s

SCSI-2 CD-ROM drive (Flint Gray) – 32X CD-ROM read – Has loading tray – Replacement for the 4X CD-ROM (Model D2992B) and 12X CD-ROM drives

4/8GB SureStore DAT 8i Single-Ended Narrow SCSI-2 DAT tape drive

12/24GB SureStore DAT 24i Single-Ended Narrow SCSI-2 DAT drive

12/24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

70GB SureStore DLT 70e Single-Ended Wide SCSI-2 external DLT drive

80GB SureStore DLT80E Low Voltage Differential SCSI external DLT drive

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

2.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor

4.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor

1.05GB hot-swap Fast SCSI-2 hard drive module (Parchment White)

2.1GB hot-swap SCSI-2 hard drive module (Dove Gray)

2.1GB hot-swap hard drive module (Flint Gray)

2.1GB hot-swap Ultra SCSI hard drive module (Quartz Gray)

4.2GB hot-swap Ultra SCSI hard drive module – 7,200 RPM

4.2GB hot-swap SCSI-2 hard drive module (Parchment White)

4.2GB hot-swap SCSI-2 hard drive module (Flint Gray)

9.1GB hot-swap Ultra SCSI-2 hard drive module (Quartz Gray)

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

4.2GB SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor

18.2GB hot-swap Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM, SCA 80-pin connector

32MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4295A) – for HP LH Pro

64MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4296A) – for HP LH Pro NetServer

128MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4297A) – for HP LH Pro NetServer

265MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4926A) – for HP LH Pro NetServer

HP LH Pro NetServer Hot Swap’ Backplane Board – for the ‘Hot Swap’ Drives – Mounts in the Rear of the ‘Hot Swap’ Drive Cage (2 Used)

HP LH Pro System (Mother) Board – with Super VGA, IDE and Two Fast/Wide SCSI-2 Controller Ports – Large Vertical Board in Center of Chassis

HP LH Pro NetServer Power Management Board – Interfaces the Power Supply (or the Two Power Supplies) to the Rest of the Computer – Includes Power Supply Input and Power Output Connectors

HP LH Pro NetServer Processor Board (Small Horizontal Board) – Has Two Processor IC Sockets, Two VRM Sockets, and Four DIMM Sockets

Remote Assistant Board (for Outside of Canada/USA) – Intelligent EISA Based Remote Management Board with Onboard NiCad Battery and Processor – Does NOT Include a Modem

PCI LAN interface board – Has RJ-45 connector for 10Base-T or 100Base-TX ethernet – PCI LAN Interface Board – Has RJ-45 Connector for 10Base-T or 100Base-TX Ethernet (P/O J3171A, 1/6 of J3172A, 1/24 of J3173A)

Dual Channel Fast Wide SCSI Disk Array Controller Board – (P/O C3610A) – Plugs into a PCI Board Slot on the System (Mother) Board

PCI dual channel fast wide SCSI disk array controller board – Dual Channel Fast Wide SCSI Disk Array Controller Board – Plugs into a PCI Board Slot on the System (Mother) Board

EISA 32-Bit fast SCSI-2 host bus adaptor

Remote assistant board – Intelligent EISA based remote management board with onboard nickel cadmium (NiCd) battery, processor, and modem (Canada and USA)

NetRAID 3-Channel Disk Array Controller – PCI Board With 3 Internal 68 Pin and 2 External 68 Pin High Density Ultra Wide SCSI Connectors (D4943A)

NetRAID 3-Channel Disk Array Controller – PCI Board With 3 Internal 68 Pin and 2 External 68 Pin High Density Ultra Wide SCSI Connectors (D4943A)

NetRAID 3-Channel disk array controller – PCI board with 3 internal 68 pin and 2 external 68 pin high density Ultra wide SCSI connectors, manual, and NetServer Navigator CD-ROM

NetRAID adapter – Includes disk array controller board, documentation, and NetServer Navigator CD-ROM

NetRAID-1 one-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

PCI 10Base-T/100Base-TX LAN board – LAN Adapter – PCI 10/100TX LAN Board for NetServer

EISA 32-BIT LAN interface board – Has 2 RJ-45 connectors – Supports both EtherTwist (10Base-T) and 100VG/802.12 – EISA 32-Bit LAN Interface Board – has 2 RJ-45 Connectors – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 – (J2577A, 1/6 of J3007A, 1/24

PCI 32-Bit LAN interface board – Has 2 RJ-45 connectors – Supports both EtherTwist (10Base-T) and 100VG/802.12 – PCI 32-Bit LAN Interface Board – has 2 RJ-45 Connectors – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585A, 1/6 of J3009A, 1/24 of J

PCI 32-BIT LAN interface board – Has RJ-45 connector – Supports both EtherTwist (10Base-T) and 100VG/802.12 – PCI 32-Bit LAN Interface Board – has RJ-45 Connector – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585B, 1/6 of J3009B, 1/24 of J3010B)

PCI Lan Interface Board – EtherTwist (10Base-T) and ThinLAN (10Base-2) Connectors (J2970A, 1/6 of J2971A, 1/24 of J2972A)

PCI LAN interface board – EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors

ISA 16-bit EtherTwist LAN interface board – Has one RJ-45 connector – Supports both 10Base-T and 100VG/802.12 – ISA 16-Bit LAN Interface Board – has One RJ-45 Connector – Supports Both Ethertwist (10BASE-T) and 100VG (802.12) (J2573A, 1/6 of J3005A, 1/24

ISA 16-BIT LAN interface board – Has one RJ-45 connector – Supports both EtherTwist (10Base-T) and 100VG (802.12)

Autoranging power supply – 100-240VAC input, 410 watts – For worldwide use – Note: The same supply is used in upper or lower position (on models that have two supplies)

Redundant power supply – Includes a 410-watt power supply, power management board, and documentation

Intel Pentium Pro processor – 200MHz (P6, 256KB Level-2 cache) – Does not include heat sink

Intel Pentium Pro processor – 200MHz (P6, 512KB Level-2 cache) – Does not include heat sink – (Part of D4867A)