PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA)

‘Windows’ keyboard assembly (Quartz Gray, 105 key) – Has attached 1.8M cable with 6-pin (Violet) mini DIN connector (Option ABF, European-French) – Replacement for the C1405B, C1405C, and D4950B Keyboards

Ribbon cable with two self adhesive cable clamps and installation instructions – 8-pin (F) connector marked ‘NetServer’ to 8-pin (F) connector marked ‘Remote Assistant’ – 1.0m (39in) cable folded to be 63.5cm (25in) long – From Remote Assistant board to c

Fast Wide internal SCSI cable – 68-pin (M) to 68-pin (M) – 23cm (9in) long – Cable C4 – Between the two hot-swap backplane boards (configuration dependent)

SCSI ribbon cable (C7) – Cable marked ‘Narrow SCSI channel B cable’ – 50-pin (F) internal connector to high density 50-pin (F) connector with latch clips for the rear panel – 55cm (21.7in) long – Cable C7 – From system board SCSI ‘B’ port to rear panel

NetServer LH cable kit – For adding drives or reconfiguring the system – Includes internal (C2) and backplane (C4) fast wide cables, and CD-ROM (C6) and external (C7) narrow cables

Floppy drive ribbon cable marked ‘Flexible disk cable’ – 34-pin (F) connector marked ‘to system board’ to a 34-pin (F) old-style edge connector and a 34-pin (F) new-style connector marked ‘to 3.5 inch flexible disk drive’ – 61.5cm (24.2in) long

Fast Wide SCSI ribbon cable (C2) – Cable marked ‘Int. SCSI cable C2-80 ohm’ – 68-pin (M) connector marked ‘System board or PCI board’ to 68-pin (M) connector marked ‘SCSI mass storage device’ – 59.9cm (23.6in) long – From hot-swap backplane boards to a PC

SCSI ribbon cable with termination – Cable is marked ‘Array SCSI cable (Narrow)’ – One 50-pin (F) connector marked ‘To array back plane’ and two 50-pin (F) connectors marked ‘To unterminated SCSI device’ – 34.3cm (13.5in) long – From CD-ROM drive to hot-s

Ribbon cable assembly – 3-pin (F) connector to 3-pin (F) connector – 30cm (11.8in) long – I2C bus cable assembly – From hot-swap backplane boards to system (mother) board (two used)

SCSI ribbon cable (C5) – Cable is marked ‘Narrow SCSI array cable’ – 50-pin (F) connector to 50-pin (F) connector marked ‘to disk array’ – 59cm (23.2in) long – From hot-swap backplane board to SCSI ‘A’ or ‘B’ port on the system (mother) board (configurati

Narrow SCSI-2 ribbon cable – Includes built-in terminator – Cable C6 – From CD-ROM drive to SCSI ‘A’ port on the system (mother) board

Ribbon cable for one IDE hard disk drive – Cable marked ‘IDE hard disk cable’ – 40-pin (F) connector to 40-pin (F) connector – 40.9cm (16.1in) long

‘Hot swap’ bezel assembly – Frame around six ‘hot swap’ drives – Includes the hot swap drive retainer lock

Hard drive tray bezel (Flint Gray) – For 3.5-inch hard drives

Bezel assembly – Plastic cover over the control panel PC board has cut outs for switches and LED activity lights

Tubeaxial fan with sensor (NMB Technologies 3610KL-04W-B49-P01) – 92mm x 92mm x 25mm thick, 12VDC, 2,850 RPM, 1.35CFM – Includes cable assembly – Mounts to the front panel (2 used)

Chassis cover – Includes front, top and both sides

Locking cover – Attaches to the front of one of the ‘Hot swap’ drive trays

Filler panel (Dove Gray) – Covers the empty Hot-Swap drive slots

5.25-inch filler panel (Quartz Gray) – For empty 5.25-inch drive bays above the Hot-Swap drive bay

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

2.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor

270MB IDE hard drive – 3.5-inch form factor – Mounts in the lower drive tray (below the CD-ROM drive)

4.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor

4.0GB Fast SCSI-2 hard drive – 3.5-inch form factor

1.05GB hot-swap Fast SCSI-2 hard drive module (Parchment White)

2.1GB hot-swap hard drive module (Flint Gray)

2.1GB ‘hot swap’ Fast SCSI-2 hard drive module – Flint Gray

2.1GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

4.2GB hot-swap Ultra SCSI hard drive module – 7,200 RPM

4.2GB hot-swap SCSI-2 hard drive module (Parchment White)

4.2GB hot-swap SCSI-2 hard drive module (Flint Gray)

4.2GB hot-swap Fast SCSI-2 hard drive module (Parchment White)

4.2GB ‘hot swap’ fast SCSI-2 hard drive module – Flint Gray

4.2GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

9.1GB hot-swap Ultra SCSI-2 hard drive module (Quartz Gray)

SCSI-2 CD-ROM drive (Flint Gray) – 32X CD-ROM read – Has loading tray – Replacement for the 4X CD-ROM (Model D2992B) and 12X CD-ROM drives

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

1GB Fast SCSI-2 hard drive – 3.5-inch form factor, low profile

1.05GB hot-swap Fast SCSI-2 hard drive module (Parchment White)

2.1GB hot-swap SCSI-2 hard drive module (Dove Gray)

2.1GB hot-swap Ultra SCSI hard drive module (Quartz Gray)

2.1GB hot-swap Fast SCSI-2 hard drive module (Dove Gray)

9.1GB ‘hot swap’ Ultra SCSI hard drive module – Quartz Gray

8MB, 70nS, 36-bit parity SIMM memory module – (D3577A) – for HP LH NetServer

32MB, 70nS, 36-bit parity SIMM memory module – (D3578A) – for HP LH NetServer

16MB manageable ECC-on-SIMM (EOS) memory module – (D3592A) – for HP LH NetServer

32MB manageable ECC-on-SIMM (EOS) memory module – (D3593A) – for HP LH NetServer

16MB, 70nS, 36-bit SIMM memory module – (D2297A) – for HP LH NetServer

4MB, 70nS, 36-bit parity SIMM memory module – (D2974A) – for HP LH NetServer

8MB manageable ECC-on-SIMM (EOS) memory module – (D3597A) – for HP LH NetServer

HP LH NetServer Remote assistant assembly – For outside of Canada/US – Without on-board modem – Remote Assistant Assy (for Outside of Canada/US) (D2967C) – without on-board Modem – When Upgrading from a D2967A/B to D2967C also Order Firmware/Software Upg

HP LH NetServer Remote Assistant PC Board Assembly (Canada/US) (D2968C) – with on-board Modem – When Upgrading from a D2968A/B to D2968C also Order Firmware/Software Upgrade Kit

HP LH NetServer System (Mother) Board – with VGA, IDE and Two Narrow SCSI-2 Controllers – Large Vertical Board in Center of Chassis

HP LH NetServer Processor Board (with a Single Socket for a 75MHz Pentium Processor IC Plus Six SIMM Sockets) – Plugs into the System (Mother) Board

HP LH NetServer ‘Hot Swap’ Backplane Board – for the ‘Hot Swap’ Drives – Mounts in the Rear of the ‘Hot Swap’ Drive Cage (2 Used)

Dual Channel Fast SCSI-2 Disk Array Controller Board – (P/O C3609A) – Plugs into an EISA Slot on the System (Mother) Bd

Dual Channel Fast Wide SCSI Disk Array Controller Board – (P/O C3610A) – Plugs into a PCI Board Slot on the System (Mother) Board

EISA 32-Bit fast SCSI-2 host bus adaptor

Remote Assistant Board (for Outside of Canada/USA) – Intelligent EISA Based Remote Management Board with Onboard NiCad Battery and Processor – Does NOT Include a Modem

Remote assistant board – Intelligent EISA based remote management board with onboard nickel cadmium (NiCd) battery, processor, and modem (Canada and USA)

EISA 32-Bit LAN Interface Board – has Two RJ-45 Connectors – One 10M bits/s (10Base-T) and One 100M bits/s (100VG/802.12) (P/O J2577A, 1/6 of J3007A, 1/24 of J3008A)

32-bit PCI LAN interface board – RJ-45 connectors – Supports both EtherTwist 10Base-T and 100VG/802.12 – (J2585B, part of J3009B, part of of J3010B)

PCI 32-Bit LAN Interface Board – has RJ-45 Connector – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585B, 1/6 of J3009B, 1/24 of J3010B)

Autoranging power supply – 100-240VAC input, 350 watts – For worldwide use – Mounts to the rear panel