Floppy drive ribbon cable – 34-pin (F) connector marked ‘to system backplane’ and a 34-pin (F) connector marked ‘to 3.5 inch flexible disk drive’ – 61cm (24in) long – Cable F7

Mass storage power cable (P3) – 22-pin (F) connector marked ‘P1’ to three cable assemblies with a 14-pin (F) connector marked ‘P2’ and four unmarked 4-pin (F) connectors – The longest cable is 50.8cm (20in) long – From backplane board to secondary hot-swa

SCSI cable with twisted pair segments (C62) – Cable is marked ‘Int SCSI cable C62’ – One 68-pin (M) connector marked ‘To iO board’ to one 68-pin (M) connector marked ‘To SCSI mass storage device’ – 55.2cm (21.8in) long

Cable kit – Two internal SCSI cables and one adapter – Used with HP NetRAID-3si disk array controller

SCSI interface cable – Low Voltage Differential/Ultra2 Single-Ended SCSI cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable – Low Voltage Differential/Ultra2 Single-Ended SCSI cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

Cable assembly – Has 14-pin (F) connectors – 9.8cm (3.9in) long – Hot-Swap cage power harness

Management port ribbon cable

IDE CD-ROM drive cable (D7) – From backplane board to IDE CD-ROM drive

Exhaust fan power cable

Ribbon cable assembly – Has 30-pin (F) connector to both a 7.8cm (3.1in) cable with DB-15 (F) connector and mounting hardware and a 16.5cm (6.5in) cable with DB-15 (F) connector and mounting hardware – From power management/interconnect board to power sup

Power supply cable assembly – A 22cm (8.7in) cable which has a 24-pin (M) connector and a 20-pin (F) connector connected using two wires to an 11cm (4.3in) cable which has a 24-pin (M) connector and a 24-pin (F) connector – From power management/interconn

Main bezel (rack mount version) – Low profile – Covers the front of the server

Front bezel – For pedestal configuration – Includes bezel lock

Main bezel (rack mount version) – Covers the front of the server

Front panel assembly bezel – Mounts over the control panel

Tubeaxial fan assembly – For the processor – Small fan that mounts on the system processor board

Hot-swap fan assembly – For the I/O boards – Mounts on the I/O board support in the middle of the chassis (Two used)

Hot-swap fan assembly – Exhaust Fan – Mounts on the rear of the chassis assembly (system processor board side)

Fan assembly – Includes two hot-swap fans mounted on a bracket – For the power supply – Slides in slot in the middle of the chassis assembly (in front of the power supplies)

Fan assembly – Includes two hot-swap fans mounted on a bracket – For the power supply – Slides in slot in the middle of the chassis assembly (in front of the power supplies)

SureStore 2U k rack kit for HP racks – 2 bay half height – Includes ‘Y’ power cable, 0.5M high density 68-pin SCSI cable, two doors, rails, and documentation

SureStore 3U k rack kit for HP racks – 4 half height or 2 full height – Includes ‘Y’ power cable, 0.5M high density 68-pin SCSI cable, two doors, rails, and documentation

NetServer LH3000/LH6000 pedestal to rack conversion kit – Includes slide rails, bezels, and accessories

Latch clip – Latch clip – Catches the arm from the cover locking latch – Mounts on the front of the chassis

Cover – Installed over the system board side of the chassis

Cover – Installed over the I/O board side of the cabinet

Cover – Large cover installed on both sides of a pedestal version or top and bottom of a rack mount version

5.25-inch filler panel (Quartz Gray) – For empty 5.25-inch drive bays above the Hot-Swap drive bay

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

Hot-swap drive bay filler panel with lock

SureStore H/A tape array 5500 – Rack mount enclosure for up to five DLT80m DLT drives – With rail kit, install guide, users manual, two power cables, and four 0.5m (1.6ft) long SCSI cables

24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive

HP SureStore Tape Rack Array – Includes rack mount enclosure for up to four removable drives, with rail kit, install guide, users manual, four power cables, two 2.5M (8.2ft) & one 0.9M (3.0ft) SCSI cable

NetServer Storage System/12 – External cabinet which can hold eight half height, or 12 low profile Ultra2 SCSI drives – Includes one Rack Storage 12 Ultra2 SCSI card

NetServer Rack Storage 12/FC – Fiber channel mass storage enclosure – Can hold 8 or 12 Ultra2 SCSI drives – Includes one copper fiber channel cable and one copper GBIC

SureStore H/A tape array 5500 – Rack mount enclosure for up to five DLT80m DLT drives – With rail kit, install guide, users manual, two power cables, and four 0.5m (1.6ft) long SCSI cables

9.1GB hot-swap Ultra3 SCSI hard drive module – 10,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1168A)

24GB internal SureStore DAT 24i Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive (Flint)

24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

20/40GB SureStore DLT 40i Single-Ended Narrow SCSI-2 internal DLT drive

6×12/24GB SureStore DAT 24×6i Single-Ended Narrow SCSI-2 internal autoloader DDS-3 (DAT) tape drive

20/40GB SureStore DAT40e external DDS-4 tape drive

20/40GB hot-swap SureStore DLT40r removable DLT drive – Includes manuals, software on a CD-ROM, DLT tape IV media, and cleaning cartridge

80GB SureStore DLT80E Low Voltage Differential SCSI external DLT drive

SureStore 418 8 slot DLT autoloader – Includes one Ultra SCSI DLT 4000 drive, six cartridge magazines, SCSI cable and terminator, and five data cartridges

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

9.1GB Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D6106A)

9.1GB hot-swap Ultra2 SCSI hard drive module – 10,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D6107A)

9.1GB Ultra Wide SCSI hard drive module – 10,000 RPM

18GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D7174A)

18.2GB hot-swap Ultra2 SCSI hard drive module – 10,000 RPM – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D7175A)

18.2GB Wide Single-Ended SCSI hard drive – 7,200 RPM

36.4GB ‘hot swap’ Ultra2 SCSI hard drive module – 10000 RPM, half height – Includes drive, hot swap tray, SCA extender, and bezel spacer – (D9419A)

18.2GB hot-swap Ultra3 SCSI hard drive module – 15,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D9421A)

18.2GB ‘hot swap’ Ultra3 SCSI hard drive module – 10000 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

18.2GB Ultra3 Wide SCSI LVD hard drive module – 10,000 RPM, 3.5-inch form factor, 1.0-inch high (Seagate ST318404LW)

9GB Ultra3 SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high

9GB Ultra3 SCSI hard drive module – 10000 RPM, 3.5in form factor, low profile

18GB Ultra3 SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high – Comes mounted on a drive tray

9.1GB hot-swap Ultra3 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1217A)

73.4GB hot-swap Ultra3 SCSI hard drive module – 10,000 RPM, half height – Includes drive, hot swap tray, SCA extender, and bezel spacer

36.4GB Ultra3 Wide SCSI LVD hard drive module – 10,000 RPM (Seagate ST336704LW)

18.2GB hot-swap Ultra3 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1216A)

64MB SIMM memory module for NetRAID 3Si disk array controller – (D7132A)

64MB, 100MHz ECC SDRAM DIMM memory module – I/O Channel Memory – Mounts on the I/O board in the NetRAID memory slot

128MB, 100MHz ECC SDRAM DIMM memory module – I/O Channel Memory – Mounts on the I/O board in the NetRAID memory slot

32MB, 100MHz non-ECC SDRAM DIMM memory module – I/O Channel Memory – Mounts on the I/O board in the NetRAID memory slot

512MB, 133MHz ECC SDRAM DIMM memory module – (D8267A) – for HP LH3000 NetServer

64MB, 133MHz ECC SDRAM DIMM memory module – (D8264A) – for HP LH3000 NetServer

128MB, 133MHz ECC SDRAM DIMM memory module – (D8265A) – for HP LH3000

256MB, 133MHz ECC SDRAM DIMM memory module – (D8266A) – for HP LH3000 NetServer

1GB, 133MHz ECC SDRAM DIMM memory module – (D8268A) – for HP LH3000 NetServer

HP LH3000 NetServer NetServer Remote Control Board with 4 Pin I2C Cable (D6028A)

HP LH3000 NetServer I/O Board – Contains four 64-bit PCI, two 64-bit and two 32-bit hot plug PCI accessory card slots -Includes extractor

HP LH3000 NetServer Power Management/Interconnect Board – Has connectors for the system processor board, I/O board, IDE drives, and system power connectors – Mounts flat in the center of the chassis

HP LH3000 NetServer System Processor Board – For up to Two PIII Processors with 133 MHz FSB – Has Four DIMM Sockets and Integrated ATI Rage IIc video controller with 2MB SGRAM

HP LH3000 NetServer Duplexing Backplane – Attaches to Hot Swap Bay Backplane to Split 6 Bay Hot Swap Cage into Two 3 Bay Units with Separate Connectors

HP LH3000 NetServer Duplexing Backplane – Attaches to Hot Swap Bay Backplane to Split 6 Bay Hot Swap Cage into Two 3 Bay Units with Separate Connectors

HP LH3000 NetServer /O Board Ultra3 SCSI – Contains four 64-bit PCI, two 64-bit and two 32-bit hot plug PCI accessory card slots

HP LH3000 NetServer Terminator board – Used in secondary processor socket for a system with only one processor

HP LH3000 NetServer Terminator board – Used in secondary processor socket for a system with only one processor

Ultra3 SCSI host adapter

NetRAID-1Si One-Channel Disk Array Controller – PCI Board with One Internal 68 Pin High Density and One External 68 Pin Ultra High Density SCSI Connector (P/O D2140A)

LAN Adapter – PCI 10/100TX LAN Board for NetServer (D5013A)

LAN Adapter – PCI 10/100TX LAN Board for NetServer

NetRAID-3Si Three-Channel Disk Array Controller – PCI Board With Three Internal 68 Pin High Density and Three External 68 Pin High Density Ultra Wide SCSI Connectors (D5955A)

NetRAID-3si three-channel disk array controller – PCI board with three internal 68 pin high density and three external 68 pin high density Ultra wide SCSI connectors

Ultra2 SCSI host adapter

TopTools remote control card with battery (Version 1) – Allows emergency remote access using LAN or modem

NetRaid-4M four-channel disk array controller W/64MB cache – PCI board with two internal 68-pin High Density and four external 68-pin Very High Density Ultra3 SCSI connectors

NetRAID-4M Four-Channel Disk Array Controller W/64MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

NetRaid-4M four-channel disk array controller W/128MB cache – PCI board with two internal 68-pin High Density and four external 68-pin Very High Density Ultra3 SCSI connectors

NetRAID-4M Four-Channel Disk Array Controller W/128MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

NetRaid-1M single-channel Ultra3 SCSI disk array controller W/32MB cache – PCI board with one internal 68-pin High Density and one external 68-pin Very High Density Ultra3 SCSI connector

NetRAID-1M Single-Channel Disk Array Controller W/32MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

NetRaid-2M dual-channel disk array controller W/64MB cache – PCI board with two internal 68-pin High Density and two external 68-pin Very High Density Ultra3 SCSI connectors

NetRAID-2M Dual-Channel Disk Array Controller W/64MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

Ultra160 LVD SCSI adapter board (Adaptec ASC-29160) – 64-bit, 66MHz PCI – External 68-pin High Density LVD connector, internal 68-pin Ultra160 LVD connector, internal 68-pin SE connector, internal 50-pin Narrow SE connector

Ultra 160 LVD SCSI adapter board (Adaptec ASC-29160) – 64 bit, 66MHz PCI – External 68 pin high density LVD connector, internal 68 pin Ultra 160 LVD connector, internal 68 pin single-ended connector, internal 50 pin narrow single-ended connector

NetRaid-2M dual-channel disk array controller W/128MB cache – PCI board with two internal 68-pin High Density and four external 68-pin Very High Density Ultra3 SCSI connectors

Gigabit LAN adapter – PCI-X 10/100/1000TX 3Com LAN card – (3Com 3C996-T)

NetRAID-1si – One-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

TopTools remote control card with battery (Version 2.0) – Allows emergency remote access using LAN or modem

NetRAID-2M Dual-Channel Disk Array Controller W/128MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

Power supply module – 300 watts

Redundant power supply module – 300 watts – Includes secondary fan tray – Plugs Into the power supply cage

Intel Pentium III processor – 533MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III ‘600EB’ processor – 600MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III ‘600EB’ processor upgrade – Includes one 600MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor with heat sink and voltage regulator module

Intel Pentium III processor upgrade – Includes one 667MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor with heat sink and voltage regulator module

Intel Pentium III processor – 733MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III processor – 800MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III ‘800EB’ processor upgrade – Includes one 800MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor with heat sink and voltage regulator module

Intel Pentium III processor upgrade – Includes one 933MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache, Slot 1) processor with heat sink and voltage regulator module

Intel Pentium III ‘533EB’ processor upgrade – Includes one 533MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor with heat sink and voltage regulator module

Intel Pentium III processor – 667MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III processor – 733MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III processor upgrade – Includes one 733MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor with heat sink and voltage regulator module

Intel Pentium III processor – 933MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III processor – 1.00GHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) – Includes heat sink

Intel Pentium III Processor upgrade – Includes one 1000MHz (Coppermine, 133MHz front side bus, 256KB Level-2 cache) processor, voltage regulator, and heat sink