PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA)

‘Windows’ keyboard assembly (Quartz Gray, 105 key) – Has attached 1.8M cable with 6-pin (Violet) mini DIN connector (Option ABF, European-French) – Replacement for the C1405B, C1405C, and D4950B Keyboards

SCSI interface cable with thumbscrews on ends – 68 pin high density (M) to 68 pin high density (M) – 0.5m (1.6ft) long

Low Voltage Differential SCSI (LVDS) interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M), 90 ohms , 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable – 50-pin high density (M) thumbscrew to 50-pin low density (M) bail lock – 1.0m (3.3ft) long

SCSI interface cable – 50-pin low density (M) bail lock to 68-pin high density (M) thumbscrew – 1.0m (3.3ft) long – (C2915A)

SCSI interface cable – 50-pin low density (M) bail lock to 68-pin high density (M) thumbscrew – 2.0m (6.6ft) long – (A3401A Option 002)

Ribbon cable with two self adhesive cable clamps and installation instructions – 8-pin (F) connector marked ‘NetServer’ to 8-pin (F) connector marked ‘Remote Assistant’ – 1.0m (39in) cable folded to be 63.5cm (25in) long – From Remote Assistant board to c

Serial management ribbon cable – 6.8cm (2.7in) cable with a 10-pin (F) connector and a DB-9 (M) connector attached to rear panel filler panel – The cable is marked ‘Remote Assist Cable’ and the filler panel is marked ‘Management Port’

Ribbon cable – 3-pin (F) connector to 3-pin (F) connector – 40cm (15.8in) long – I2C bus cable assembly (E) – From system backplane board to hot-swap backplane board

Floppy drive ribbon cable marked ‘Floppy disk’ – 34-pin (F) connector marked ‘to system board’ to 34-pin (F) connector marked ‘to 3.5 inch flexible disk drive’ – 50.2cm (19.8in) long – Cable C

IDE CD-ROM drive ribbon cable marked ‘IDE cable D6’ – 40-pin (F) connector marked ‘To system board’ to a 40-pin (F) connector marked ‘To IDE CD-ROM’ – 17.1cm (6.8in) long – Cable B – From system backplane board to IDE devices

Terminated 90 ohm SCSI ribbon cable kit (C42) with 68-pin (M) connectors – A cable clamp, a connector marked ‘To system board’, four connectors marked ‘To Unterminated SCSI Device’, and a 50-pin (F) to 68-pin (F) adapter – 86.1cm (33.9in) long – Wide SCSI

SCSI ribbon cable kit (C52) – A 68-pin (F) to 50-pin (F) adapter and a cable marked ‘Int/Ext SCSI cable C52-90 ohm’ with 68-pin (M) connectors marked ‘to Sys Bd’, ‘to unterminated SCSI device’, and ‘to Mass Storage Device’ – 70.4cm (27.7in) long – Wide SC

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 0.9m (3.0ft) long

SCSI interface cable – 50 pin low density (M) bail locks to 68 pin high density (M) thumbscrews – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 128 Ohms – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 90 Ohms – 1.5m (4.9ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 1.5m (4.9ft) long

SCSI interface cable with thumbscrews on both ends – Ultra flexible 68 pin high density (M) to 68 pin high density (M) – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 0.9m (3.0ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 1.5m (4.9ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – Highly flexible 68 pin high density (M) to 68 pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – Highly flexible 68 pin high density (M) to 68 pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – Highly flexible 68-pin high density (M) to 68-pin high density (M) – 90 Ohms – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – Highly flexible 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – Highly flexible 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

NetRAID controller to Rack Storage/8 cable kit – Includes a 68-pin cable from third channel of D4943A controller to rear panel and a 2.5m (8.2ft) 68-pin high density cable with thumbscrews

Wide SCSI cable kit – Internal cable connected to controller board – Contains one cable for NetServer LCII and one cable for NetServer E-series – From D5025A controller board to common tray for duplexing

SCSI interface cable – Low Voltage Differential/Ultra2 Single-Ended SCSI cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable – 50-pin low density (M) bail lock to 50-pin high density (M) latch/clip – 1.5m (4.9ft) long – (K2285)

SCSI interface cable – 50-pin low density (M) bail lock to 50-pin high density (M) latch/clip – 1.0m (3.3ft) long – (K2286)

SCSI cable kit with termination (C82) – Self-adhesive cable clamp and a cable marked ‘Int SCSI cable C82-90 ohm’ – Three 68-pin (M) connectors, one marked ‘to system board’, the others marked ‘to Unterminated SCSI device’ – 65.3cm (25.7in) long – Wide SCS

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 128 Ohms – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 90 Ohms – 0.5m (1.6ft) long

Low Voltage Differential/Ultra2 Single-Ended SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

‘Hot swap’ bezel assembly – Frame around 3 ‘hot swap’ drives

Front bezel assembly

Processor fan and bracket assembly – (P/O some accessory kits) – If Installed, it is mounted on the right side of the processor bracket

System fan – Mounts on the rear of the cabinet

NetServer LCIIs rack mount kit – Rack mount one or two LCIIs – Contains stationary base, dual sliding shelves, blank panel, and ear panels for the column – (Quartz Gray)

8-port Console Switch – Connect up to eight computers to a single monitor, keyboard, and mouse – Includes rack mounting hardware – Must order connecting cables separately

Adapter – 68-pin high density (F) to 50-pin (F) – Used to connect 68-pin (M) ribbon cable to 50-pin (M) Narrow SCSI device – (C5710A)

Adapter – 68-pin high density female to 50-pin female – Used to connect 68-pin male ribbon cable to 50-pin male Narrow SCSI device

Adapter – 68-pin high density female to 50-pin female – Used to connect 68-pin male ribbon cable to 50-pin male Narrow SCSI device

Heat sink clip – Heat sink clip for Pentium II module – Two used

Top cover assembly

Side cover assembly

5.25-inch filler panel (Quartz Gray) – For empty 5.25-inch drive bays above the Hot-Swap drive bay

Hot Swap drive filler panel (Flint Gray) – For empty Hot-Swap drive slots

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

2 button PS/2 serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-din connector

NetServer Storage System/6 – External cabinet which can hold up to two half-height non-hot-swap Fast SCSI-2 drives and up to six hot-swap drive modules – Includes cabinet with 6 bays, 2 common tray shelves, dual SCSI backplane, and redundant power s

NetServer Storage System/6 – External cabinet which can hold up to two half-height non-hot-swap Fast SCSI-2 drives and up to six hot-swap drive modules – Includes cabinet with 6 bays, 2 common tray shelves, dual SCSI backplane, and redundant power s

Single-ended SCSI active terminator – Has 68 pin high density (M) connector with thumbscrews

2GB external SureStore DAT2000e Single-Ended Narrow SCSI-2 DDS-1 tape drive

HP SureStore 5000e – External 2/4GB DDS (DAT) drive – Single-ended narrow SCSI-2

4/8GB SureStore DAT 8i Single-Ended Narrow SCSI-2 DAT tape drive

12/24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

20/40GB SureStore DLT 40i Single-Ended Narrow SCSI-2 internal DLT drive

70GB SureStore DLT 70e Single-Ended Wide SCSI-2 external DLT drive

6×12/24GB SureStore DAT 24×6i Single-Ended Narrow SCSI-2 internal autoloader DDS-3 (DAT) tape drive

80GB SureStore DLT80E Low Voltage Differential SCSI external DLT drive

80GB SureStore DLT80E Low Voltage Differential SCSI external DLT drive

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

1.05GB hot-swap Fast SCSI-2 hard drive module (Parchment White)

2.1GB hot-swap hard drive module (Flint Gray)

4.2GB hot-swap Ultra SCSI hard drive module – 7,200 RPM

4.2GB hot-swap SCSI-2 hard drive module (Parchment White)

4.2GB hot-swap SCSI-2 hard drive module (Flint Gray)

9.1GB hot-swap Ultra SCSI-2 hard drive module (Quartz Gray)

IDE CD-ROM drive with integral loading tray – 24X CD-ROM read

IDE CD-ROM drive – 48X CD-ROM read (Mitsumi CRMC-FX4820T) – Has front panel headphone jack and volume control

18.2GB Wide Single-Ended SCSI hard drive – 7,200 RPM

4/8GB external SureStore DAT 8e Single-Ended Narrow SCSI-2 DAT tape drive

12/24GB SureStore DAT 24i Single-Ended Narrow SCSI-2 DAT drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

2.1GB hot-swap SCSI-2 hard drive module (Dove Gray)

2.1GB hot-swap Ultra SCSI hard drive module (Quartz Gray)

4.2GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM

4.2GB Ultra Wide SCSI hard drive – 7,200 RPM

9.1GB Ultra Wide SCSI hard drive module – 7,200 RPM

18.2GB hot-swap Ultra Wide SCSI hard drive module – 7,200 RPM

9.1GB hot-swap Ultra Wide SCSI hard drive module – 10,000 RPM, SCA 80-pin connector

9.1GB Ultra Wide SCSI hard drive module – 10,000 RPM

512kB, 50ns EDO VRAM video memory IC – Plugs into sockets on system processor board – (Two or four required, 1MB kit is D4219A) – Installing two IC’s will upgrade to 2MB total of video memory

64MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4296A) for HP LC2 NetServer

32MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4295A) for HP LC2 NetServer

128MB, 60nS, 72-bit EDO (Extended Data Output) DIMM memory module – (D4297A) -for HP LC2 NetServer

64MB SIMM memory module for NetRAID 3Si disk array controller – (D7132A) for HP LC2

HP LC2 Terminator board – Used in secondary processor socket for a system with only one processor

HP LC2 NetServer Remote Assistant Assy (for Outside of Canada/US) (D2967C) – without on-board Modem – When Upgrading from a D2967A/B to D2967C also Order Firmware/Software Upgrade Kit

HP LC2 NetServer Remote Assistant PC Board Assembly (Canada/US) (D2968C) – with on-board Modem – When Upgrading from a D2968A/B to D2968C also Order Firmware/Software Upgrade Kit

HP LC2 NetServer Remote Assistant Board (for Outside USA and Canada) (D2969C) – EISA Intelligent Remote Management Board with Onboard NiCad Battery, Processor, & Modem (Does NOT Include the LAM)

HP LC2 NetServer Hot Swap’ Backplane Board – for Three ‘Hot Swap’ Drives – Mounts in the the Rear of the ‘Hot Swap’ Drive Cage

HP LC2 NetServer System (Mother) Board – with Super VGA Video, Ultra SCSI Controller, IDE Controller – Large Vertical Board in Center of Chassis

HP LC2 NetServer System Backplane Board – Large Horizontal Board in Center of the NetServer – Has Sockets for Add-in ISA or PCI Boards

NetRAID 3-Channel Disk Array Controller – PCI Board With 3 Internal 68 Pin and 2 External 68 Pin High Density Ultra Wide SCSI Connectors (D4943A)

NetRAID-1Si One-Channel Disk Array Controller – PCI Board with One Internal 68 Pin High Density and One External 68 Pin Ultra High Density SCSI Connector (P/O D2140A)

NetRAID 3-Channel disk array controller – PCI board with 3 internal 68 pin and 2 external 68 pin high density Ultra wide SCSI connectors, manual, and NetServer Navigator CD-ROM

NetRAID-1 One-Channel Disk Array Controller – PCI Board With One Internal 68 Pin High Density and One External 68 Pin High Density Ultra Wide SCSI Connector (D4992A)

NetRAID-1 one-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

LAN Adapter – PCI 10/100TX LAN Board for NetServer (D5013A)

NetRAID-3Si Three-Channel Disk Array Controller – PCI Board With Three Internal 68 Pin High Density and Three External 68 Pin High Density Ultra Wide SCSI Connectors (D5955A)

NetRAID-3si three-channel disk array controller – PCI board with three internal 68 pin high density and three external 68 pin high density Ultra wide SCSI connectors

32-bit PCI LAN interface board – RJ-45 connectors – Supports both EtherTwist 10Base-T and 100VG/802.12 – (J2585B, part of J3009B, part of of J3010B)

Wide SCSI Host Adapter Board (D5025A) – Installed in PCI Socket on System Backplane Board

PCI Wide SCSI host adapter board – Wide SCSI Host Adapter Board – Installed in PCI Socket on System Backplane Board – May Need Cables D5968A and D6001A

Power supply assembly – 350 watts – NOTE: The fan inside the power supply is not available separately

Intel Pentium processor – 66MHz for HP LC 5/66

Intel Pentium II processor – 333MHz (Klamath, 66MHz front side bus, 512KB Level-2 cache, Slot 1, ECC) – Includes heat sink

Intel Pentium II processor – 300MHz (Klamath, 66MHz front side bus, 512KB Level-2 cache, Slot 1, ECC) – Includes heat sink