PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA)

Ribbon cable marked ‘Management port cable’ – 10-pin (F) connector to DB-9 (M) external connector – 8.3cm (3.3in) long

IDE CD-ROM drive ribbon cable marked ‘IDE CD-ROM drive D12’ – 40-pin (F) connector marked ‘To system board’ to a 40-pin (F) connector marked ‘To IDE CD-ROM drive’ – 40.6cm (16.0in) long

Ribbon cable marked ‘Control panel’ – 20-pin (F) connector to 20-pin (F) connector – 36cm (14.2in) long

IDE floppy drive ribbon cable marked ‘Floppy disk cable F81’ – 34-pin (F) connector marked ‘to system board’ to 34-pin (F) connector marked ‘to 3.5 inch flexible disk drive’ – 40.4cm (15.9in) long

Power cable kit – Line filter with C14 (M) connector for power in and two spade lugs (M) for power out and 48cm (19 inch) power cord with two spade lug (F) connectors for power in and C13 (F) connector for power out and a ground wire with ring terminal

Cable assembly – Has 2-pin (F) connectors on each end – 20.4cm (8.0in) long – SCSI terminator board power cable

SCSI ribbon cable with termination (C17) – Cable is marked ‘Ext SCSI/Riser board cable C17’ – Has a 68-pin (M) connector marked ‘To riser board’ and a 68-pin (M) connector marked ‘To external SCSI port’ – 40.1cm (15.8in) long

Ribbon cable marked ‘I2C cable I21’ – 3-pin (F) connector to 3-pin (F) connector – 20.1cm (7.9in) long

Ultra2 Wide SCSI ribbon cable (C18) – Cable marked ‘Int/Ext SCSI cable’ – Has a 68-pin (M) connector marked ‘to SF-2 board’, a 68-pin (M) connector marked ‘to rizer board’, and a 68-pin (M) connector marked ‘to external SCSI port’ – 68cm (26.9in) long

SCSI interface cable – Low Voltage Differential/Ultra2 Single-Ended SCSI cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

Front bezel kit – With HP name plate

Front bezel kit – For 3rd party use

Three fan assembly – Includes three fans

Rack mount kit – Used to mount 1 or 2 DLT 418/718/818 autoloaders in HP 19-inch racks – Includes shelf, bezel, filler panel, and hardware

Rack mount kit for LPr NetServer – Includes rack mount rails – Rails mount on side of chassis

Universal monitor rack mount kit – For any monitor up to 19-inch and 100 pounds – Quartz Gray

Universal monitor rack mount kit (Quartz Gray) – For any monitor up to 19-inch (max height 46cm (18.1-inches)) and 100 pounds

Rack mount kit – Used to mount 1 or 2 DLT 418/718/818 autoloaders in HP 19-inch racks – Includes shelf, bezel, filler panel, and hardware

8-port Console Switch – Connect up to eight computers to a single monitor, keyboard, and mouse – Includes rack mounting hardware – Must order connecting cables separately

4-port Console Switch (Quartz Gray) – Connect up to four computers to a single monitor, keyboard, and mouse – Includes hardware, user manual, and power cable

4-port Console Switch (Quartz Gray) – Connect up to four computers to a single monitor, keyboard, and mouse – Includes connecting cables

Chassis top cover assembly

Side cover kit for Rack System/E41 Cabinet – Includes eight 8U panels and two 9U panels – Panels are snap on/off molded plastic

Side cover kit for Rack System/E33 or U33 Cabinet – Includes six 8U panels and two 9U panels – Panels are snap on/off molded plastic

Side cover kit – Includes four 8U panels and two 9U panels – Panels are snap on/off molded plastic – For Rack System/E25 or U25 Cabinet

1U rackmount filler panels – For covering the empty slots on the front of the rack cabinet – Package of 6 panels

2 button PS/2 serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-din connector

PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B)

Hot-swap drive bay filler panel with lock

24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive

NetServer Storage System/6 – External cabinet which can hold up to two half-height non-hot-swap Fast SCSI-2 drives and up to six hot-swap drive modules – Includes cabinet with 6 bays, 2 common tray shelves, dual SCSI backplane, and redundant power s

24GB external SureStore DAT 24e Single-Ended Narrow SCSI-2 DDS-3 DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

6×12/24GB external SureStore DAT 24×6e Single-Ended Narrow SCSI-2 six slot magazine autoloader DAT tape drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

20/40GB external SureStore DLT 40e Single-Ended Narrow SCSI-2 DLT tape drive

SureStore DLT library 4115wr 15 slot rack mount tape library – Includes one Fast Wide SCSI DLT 4000 drive, rack slides, three magazines, barcode reader, and accessories

SureStore DLT library 4215wr 15 slot rack mount tape library – Includes two Fast Wide SCSI DLT 4000 drives, rack slides, three magazines, barcode reader, and accessories

SureStore 418 8 slot DLT autoloader – Includes one Ultra SCSI DLT 4000 drive, six cartridge magazines, SCSI cable and terminator, and five data cartridges

1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B)

IDE slimline CD-ROM drive – 24X CD-ROM read

4.2GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM, low profile

9.1GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D6106A)

9.1GB ‘hot swap’ Ultra2 SCSI hard drive module – 7200 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

9.1GB hot-swap Ultra2 SCSI hard drive module – 10,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D6107A)

9.1GB ‘hot swap’ Ultra2 SCSI hard drive module – 10000 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

18GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D7174A)

18GB ‘hot swap’ Ultra2 SCSI hard drive module – 7200 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

18.2GB hot-swap Ultra2 SCSI hard drive module – 10,000 RPM – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D7175A)

18GB ‘hot swap’ Ultra2 SCSI hard drive module – 10000 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

18.2GB hot-swap Ultra3 SCSI hard drive module – 15,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (D9421A)

9.1GB hot-swap Ultra3 SCSI hard drive module – 10,000 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1168A)

18.2GB hot-swap Ultra3 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1216A)

73.4GB hot-swap Ultra3 SCSI hard drive module – 10,000 RPM, half height – Includes drive, hot swap tray, SCA extender, and bezel spacer

4.2GB hot-swap Ultra2 SCSI hard drive module – 7,200 RPM

36.4GB ‘hot swap’ Ultra2 SCSI hard drive module – 10000 RPM, half height – Includes drive, hot swap tray, SCA extender, and bezel spacer – (D9419A)

18.2GB ‘hot swap’ Ultra3 SCSI hard drive module – 10000 RPM, low profile – Includes drive, hot swap tray, SCA extender, and bezel spacer

9.1GB hot-swap Ultra3 SCSI hard drive module – 7,200 RPM, low profile – Includes drive, hot-swap tray, SCA extender, and bezel spacer – (P1217A)

73.4GB ‘hot-swap’ Ultra3 SCSI hard drive – 10000 RPM, low profile – Includes hot-swap tray

512kB, 50ns EDO VRAM video memory IC – For system boards with an integrated video controller ONLY (1MB kit is D4219A)

128MB, 100MHz registered ECC SDRAM DIMM memory module for HP LPr NetServer

256MB, 100MHz registered ECC SDRAM DIMM memory module for HP LPr NetServer

64MB SIMM memory module for NetRAID 3Si disk array controller – (D7132A)

64MB, 100MHz registered ECC SDRAM DIMM memory module for HP LPr NetServeR

HP LPr NetServer Terminator Board – Installed in a Processor Socket When the Processor is Not Installed

HP LPr Hot Swap’ SCSI Backplane Board – for the ‘Hot Swap’ SCSI Drives – Mounts in the Rear of the ‘Hot Swap’ Drive Cage

LPr NetServer SCSI Management Board – Manages SCSI Drive Activity – Plugs Into the Hot Swap SCSI Backplane Board

HP LPr SCSI Terminator Board

HP LPr Backplane board – Has four PCI slots one taken by pre-installed network adapter card

HP LPr NetServer System processor board – Dual processor with integrated Ultra2 SCSI controller and Super VGA graphics controller

NetRAID-1si – One-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

NetRAID 3-Channel Disk Array Controller – PCI Board With 3 Internal 68 Pin and 2 External 68 Pin High Density Ultra Wide SCSI Connectors (D4943A)

NetRAID 3-Channel disk array controller – PCI board with 3 internal 68 pin and 2 external 68 pin high density Ultra wide SCSI connectors, manual, and NetServer Navigator CD-ROM

NetRAID-1 one-channel disk array controller – PCI board with one internal 68 pin high density and one external 68 pin high density Ultra wide SCSI connector

LAN Adapter – PCI 10/100TX LAN Board for NetServer

LAN Adapter – PCI 10/100TX LAN Board for NetServer

Wide SCSI Host Adapter Board (D5025A) – Installed in PCI Socket on System Backplane Board

Wide SCSI Host Adapter Board – Installed in PCI Socket on System Backplane Board – May Need Cables D5968A and D6001A

NetRAID-3Si Three-Channel Disk Array Controller – PCI Board With Three Internal 68 Pin High Density and Three External 68 Pin High Density Ultra Wide SCSI Connectors (D5955A)

NetRAID-3si three-channel disk array controller – PCI board with three internal 68 pin high density and three external 68 pin high density Ultra wide SCSI connectors

Fiber channel array – Redundant module with two fiber channel ports and two very high density 68-pin SCSI connectors

NetServer fiber channel array – Redundant, dual ported fiber channel connection from host to the NetServer includes three 3M copper fiber channel cables and three copper GBIC

Ultra2 SCSI host adapter

Ultra3 SCSI host adapter

TopTools remote control card with battery (Version 1) – Allows emergency remote access using LAN or modem

NetRAID-4M Four-Channel Disk Array Controller W/64MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

NetRAID-4M Four-Channel Disk Array Controller W/128MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

PCI 32-Bit LAN Interface Board – has RJ-45 Connector – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585B, 1/6 of J3009B, 1/24 of J3010B)

TopTools remote control card with battery (Version 2.0) – Allows emergency remote access using LAN or modem

NetRAID-1M Single-Channel Disk Array Controller W/32MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

NetRAID-2M Dual-Channel Disk Array Controller W/64MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

Ultra 160 LVD SCSI adapter board (Adaptec ASC-29160) – 64 bit, 66MHz PCI – External 68 pin high density LVD connector, internal 68 pin Ultra 160 LVD connector, internal 68 pin single-ended connector, internal 50 pin narrow single-ended connector

NetRAID-2M Dual-Channel Disk Array Controller W/128MB Cache – PCI Board With Two Internal 68 Pin High Density and four External 68 Pin Very High Density Ultra3 SCSI Connectors

Gigabit LAN adapter – PCI-X 10/100/1000TX 3Com LAN card – (3Com 3C996-T)

NetRAID-1 One-Channel Disk Array Controller – PCI Board With One Internal 68 Pin High Density and One External 68 Pin High Density Ultra Wide SCSI Connector (D4992A)

Intel Pentium II processor – 400MHz (Deschutes, 100MHz front side bus, 512KB Level-2 cache, SECC-2, Slot 1) – Includes heat sink for HP LPr PIII/400 NetServer

Intel Pentium II processor upgrade – Includes one 450MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor foR HP LPr PII/450 NetServer

Intel Pentium II processor upgrade – Includes one 400MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor for HP LPr PIII/500 NetServer

Intel Pentium III processor – 600MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache, Slot 1) – Requires processor fan accessory (D8595A) foR HP LPr PIII/600 NetServer

Intel Pentium III processor upgrade – Includes one 600MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache) processor for HP LPr PIII/600 NetServer

Intel Pentium III processor – 650MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) for HP LPr PIII/650 NetServer

Intel Pentium III processor upgrade – Includes one 650MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) processor for HP LPr PIII/650 NetServer

Intel Pentium III processor – 750MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) for HP LPr PIII/750 NetServer

Intel Pentium III processor upgrade – Includes one 750MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) processor for HP LPr PIII/750 NetServer

Intel Pentium III processor – 800MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) for HP LPr PIII/800 NetServer

Intel Pentium III processor upgrade – Includes one 800MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) processor for HP LPr PIII/800 NetServer

Intel Pentium III processor – 850MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) for HP LPr PIII/850 NetServer

Intel Pentium II processor upgrade – Includes one 400MHz (Deschutes, 512KB Level-2 cache, Slot 1) processor foR HP LPi PII/400 NetServer

Intel Pentium III processor upgrade – Includes one 550MHz (Katmai, 100MHz front side bus, 512KB Level-2 cache) processor for HP LPr PIII/550 NetServer

Intel Pentium III processor upgrade – Includes one 700MHz (Coppermine, 100MHz front side bus, 256KB Level-2 cache) processor for HP LPr PIII/700 NetServer

Intel Pentium III processor upgrade – Includes one 850MHz (Coppermine, 256KB Level-2 cache) processor for HP LPr PIII/850 NetServer