DC-DC converter module (Yokogawa PS602) – 185-400VDC input – 5VDC output, 65A, 325 watts – (Up to four modules MAY be used depending on number of memory and bus converter boards installed, in slots P5,P6,P7 and P13)

Fan power cable assembly – In fan chassis assembly

Fan speed sensor cable assembly – In fan chassis asy

Power cable – From 350V DC high voltage power supply to HP-PB I/O cardcage

External link cable with thumbscrews on both ends – 80-pin (M) connectors on each end – 10m (32.8ft) long – From Upper Bus Converter board to Lower Bus Converter board mounted external of SPU

External link cable with thumbscrews on both ends – 80-pin (M) connectors on each end – 1.0m (3.3ft) long – From Upper Bus Converter board to Lower Bus Converter board

Cable assembly – Power fail correction (PFC) interface cable – From 350V DC high voltage power supply to HP-PB I/O cardcage

Power fail recovery battery cable – Includes fuse and fuseholder

Power fail recovery battery jumper cable – (three used)

AC power cable assembly – 15-pin (F) connector to 25cm (10in) power cord, 25cm (10in) cable with 10-pin (F) connector, and two 9cm (3.5in) ground wires with ring terminals – To power supply in HP-PB I/O card cage

Ribbon cable and power switch assembly – A 68cm (26.8in) ribbon cable with 10-pin (F) connectors on each end and one attached power switch – For power/LED – In external I/O card cage

Chassis assembly (Metal) – Upper front card cage structure

Chassis assembly (Metal) – Upper rear card cage structure

Tubeaxial fan – 105mm (4.126in) mounting hole spacing, 38.1mm (1.5in) thick, 115VAC, 50-60Hz, 120CFM – Mounts in the fan tray (Two used)

Tubeaxial fan (Papst-Motoren Gmbh 6224/4) – 203mm (8.0in) diameter, 51mm (2.0in) thick), 24VDC, 241CFM – Mounts in the fan chassis assembly (11 used)

Power supply fan assembly – For 350V DC supply – In bottom front

Fan assembly – 12cm (4.7in) tubeaxial fan with an attached 27.5cm (10.8in) long two wire power cable with a 3-pin (F) connector – In external I/O card cage

Main power switch assembly – Mounts in the upper front panel (Forehead) assembly – For 120V operation ONLY

Cabinet top cover – Over processor/memory bus card cage

Cover – For power fail recovery batteries

AC input cover – Located on lower right rear corner of SPU cabinet

Cabinet top cover assembly – Solid

Left or right side cover – For 1.6m cabinet (2 used)

Cabinet top cover assembly – Vented

Left side panel – For computer cabinet

Right side panel (L-shaped)

Backplane panel assembly – Supports backplane – Does not include PC board

Lower front panel (1.6M, 2.0M) – Mounts to the front of the cabinet base

Upper front panel (Forehead) – Has a cutout for the power switch – Power switch NOT included

128MB ECC memory board upgrade

256MB ECC memory board upgrade

H9000 T520 Control panel board – Control Panel Board – on Front Top of Computer

H9000 T520 Fan controller board – Fan Controller Board – in Rear of Fan Chassis Assembly

HP9000 T520 Precision Bus Adapter(L-Shaped) – Adapts CIO Bd to Backplane

HP9000 T520 Backplane Board – in Center of HP-PB I/O Card Cage

HP9000 T520 Backplane Board – in Center of HP-PB I/O Card Cage

HP9000 T520 Backplane Board – in the Center of the Upper Card Cage (PMB) – Has Front and Rear Slots for the Processor(s), Memory, and Bus Converter Boards

HP9000 T520 Lower bus converter board – Controls HP-Precision bus

HP9000 T520 Upper bus converter board – Plugs into Processor/Memory Bus

Power System Control Module Bd – in HP-PB I/O Card Cage

HP9000 T520 Power System Control Module Bd – in HP-PB I/O Card Cage

Service Processor Board – Plugs into the Rear (PMB) Upper Card Cage Slot (Labeled SP)

HP9000 T520 LED Board – on Lower Right Front of External I/O Card Cage

HP9000 T520 128MB ECC memory board

HP9000 T520 512MB ECC memory board

HP9000 T520 768MB ECC memory board

HP9000 T520 Processor (Mother) Board – Does NOT Include the Processor Module(s) – Plugs into the Upper Card Cage (PMB) Backplane Board

Fiberoptic Peripheral Interface Board – for the HP-PB I/O Board Slot (P/O 28615A or 28616A)

Fiber-Optic peripheral interface board – For the HP-PB I/O board slot – Includes 30m (98ft) Fiber-Optic cable

HP-PB LAN console interface board

LAN Link (EtherNet or IEEE 802.3) Interface Board – for the HP-PB I/O Board Slot (P/O J2146A)

Fast Wide Differential SCSI Host Adapter Board – for the HP-PB I/O Board Slot (P/O 28696A)

Fast wide differential SCSI-2 host adapter board kit – Includes 2.5m (8.2ft) SCSI cable – For the HP-PB I/O board slot

Remarketed fast wide differential SCSI-2 host adapter board – For the HP-PB I/O board slot – Includes SCSI cable

CIO HP-IB Interface Board (27110B or 27113A)

10/100Base-TX LAN adapter interface board – For the HP-PB I/O board slot – Auto senses between 10Mbps and 100Mbps

32 Channel RS-232C Direct Connect MUX Board (with RJ-45 Connectors) – for the HP-PB I/O Board Slot (P/O J2096A)

32 Channel RS-232C Direct Connect MUX Board (with RJ-45 Connectors) – for the HP-PB I/O Board Slot

Switching power supply (Delta Electronics SMP-264AB REV. B) – 120/240VAC input, 50-60Hz – Three DC outputs, 260 watts – In HP-PB I/O card cage

Switching power supply (Delta Electronics SMP-264AB REV. B) – 120/240VAC input, 50-60Hz – Three DC outputs, 260 watts – In HP-PB I/O card cage

High voltage power supply (Astec AA50090) – 169-269VAC input, 350VDC nominal output, 6.3A, 2200 watts – With active power factor correction (PFC) and battery backup – Mounts in the right lower rear of the computer

DC-DC converter module (Yokogawa PS603) – 185-400VDC input – 24VDC output, 325 watts – Supply for the fan power

DC-DC converter module (Yokogawa PS601) – 185-400VDC input – +5VDC output, 130A, 650 watts – (Up to four modules MAY be used depending on number of processor boards installed – Used in slots P1, P10, P2 and P8)

HP PA-RISC processor module – Includes 120MHz processor and 1MB cache – Plugs into the processor (mother) board (One or two can be plugged into each processor board)