DC-DC converter module (Yokogawa PS602) – 185-400VDC input – 5VDC output, 65A, 325 watts – (Up to four modules MAY be used depending on number of memory and bus converter boards installed, in slots P5,P6,P7 and P13)

3.3V DC to DC power converter

5.0V DC to DC power converter

HP-PB I/O bus converter

HP-HSC bus converter

SCSI interface cable – 50 pin high density (M) thumbscrew to 50 pin low density (M) bail lock – 2.5m (8.2ft) long

Cable assembly – 6-pin DIN to 25-pin (M) – 5m (16ft) long

Control panel cable

Support cable

Stadby ready switch cable

Fan power cable assembly – In fan chassis assembly

Fan speed sensor cable assembly – In fan chassis asy

Power cable – From 350V DC high voltage power supply to HP-PB I/O cardcage

External link cable with thumbscrews on both ends – 80-pin (M) connectors on each end – 10m (32.8ft) long – From Upper Bus Converter board to Lower Bus Converter board mounted external of SPU

External link cable with thumbscrews on both ends – 80-pin (M) connectors on each end – 1.0m (3.3ft) long – From Upper Bus Converter board to Lower Bus Converter board

Cable assembly – Power fail correction (PFC) interface cable – From 350V DC high voltage power supply to HP-PB I/O cardcage

Power fail recovery battery jumper cable

AC power cable assembly – 15-pin (F) connector to 25cm (10in) power cord, 25cm (10in) cable with 10-pin (F) connector, and two 9cm (3.5in) ground wires with ring terminals – To power supply in HP-PB I/O card cage

Ribbon cable and power switch assembly – A 68cm (26.8in) ribbon cable with 10-pin (F) connectors on each end and one attached power switch – For power/LED – In external I/O card cage

MUX ‘Y’ cable

Chassis assembly (Metal) – Upper front card cage structure

Chassis assembly (Metal) – Upper rear card cage structure

Tubeaxial fan – 105mm (4.126in) mounting hole spacing, 38.1mm (1.5in) thick, 115VAC, 50-60Hz, 120CFM – Mounts in the fan tray (Two used)

Tubeaxial fan (Papst-Motoren Gmbh 6224/4) – 203mm (8.0in) diameter, 51mm (2.0in) thick), 24VDC, 241CFM – Mounts in the fan chassis assembly (11 used)

Power supply fan assembly – For 350V DC supply – In bottom front

Fan assembly – 12cm (4.7in) tubeaxial fan with an attached 27.5cm (10.8in) long two wire power cable with a 3-pin (F) connector – In external I/O card cage

Main power switch assembly – Mounts in the upper front panel (Forehead) assembly – For 120V operation ONLY

Main power switch assembly – Mounts in the upper front panel (Forehead) assembly – For 220V operation ONLY

EMC clip for the HSC bus converter

Cover plate – For empty single high HP-PB I/O board slots (Includes the two captive screws)

Cabinet top cover – Over processor/memory bus card cage

Cover – For power fail recovery batteries

Configuration block cover

650W DC voltage converter cover

325W DC voltage converter cover

Front cover assembly – For internal HP-PB I/O card cage

Rear cover assembly – For internal HP-PB I/O card cage

Single cover

AC input cover – Located on lower right rear corner of SPU cabinet

Cabinet top cover assembly – Solid

Left or right side cover – For 1.6m cabinet (2 used)

Cabinet top cover assembly – Vented

Left side panel – For computer cabinet

Right side panel (L-shaped)

Backplane panel assembly – Supports backplane – Does not include PC board

Lower front panel (1.6M, 2.0M) – Mounts to the front of the cabinet base

Upper front panel (Forehead) – Has a cutout for the power switch – Power switch NOT included

128MB ECC memory board upgrade

256MB ECC memory board upgrade

4MB L2 cache module

256MB ECC DIMM memory module for HP9000 T600

1GB ECC DIMM memory module

HP9000 T600 Single-Ended SCSI-2/Centronics host adapter board

HP9000 T600 Control Panel Board – on Front Top of Computer

HP9000 T600 Fan Controller Board – in Rear of Fan Chassis Assembly

HP9000 T600 Backplane Board – in Center of HP-PB I/O Card Cage

HP9000 T600 Backplane Board – in Center of HP-PB I/O Card Cage

HP9000 T600 Backplane Board – in the Center of the Upper Card Cage (PMB) – Has Front and Rear Slots for the Processor(s), Memory, and Bus Converter Boards

HP9000 T600 Lower bus converter board – Controls HP-Precision bus

HP9000 T600 Upper bus converter board – Plugs into Processor/Memory Bus

HP9000 T600 Power System Control Module Bd – in HP-PB I/O Card Cage

HP9000 T600 Power System Control Module Bd – in HP-PB I/O Card Cage

HP9000 T600 Service Processor Board – Plugs into the Rear (PMB) Upper Card Cage Slot (Labeled SP)

HP9000 T600 LED Board – on Lower Right Front of External I/O Card Cage

128MB ECC memory board

512MB ECC memory board

768MB ECC memory board

HP9000 T600 System processor board – Supports one or two processor daughter boards

Fiberoptic Peripheral Interface Board – for the HP-PB I/O Board Slot (P/O 28615A or 28616A)

Fiber-Optic peripheral interface board – For the HP-PB I/O board slot – Includes 30m (98ft) Fiber-Optic cable

HP-PB LAN console interface board

LAN Link (EtherNet or IEEE 802.3) Interface Board – for the HP-PB I/O Board Slot (P/O J2146A)

Single-ended SCSI-2 and Centronics host adapter board – Includes a 1.0m (3.3ft) SCSI cable – For the HP-PB I/O board slot

Fast Wide Differential SCSI Host Adapter Board – for the HP-PB I/O Board Slot (P/O 28696A)

Fast wide differential SCSI-2 host adapter board kit – Includes 2.5m (8.2ft) SCSI cable – For the HP-PB I/O board slot

Remarketed Fast Wide Differential SCSI Host Adapter Board – for the HP-PB I/O Board Slot

CIO HP-IB Interface Board (27110B or 27113A)

10/100Base-T LAN Adapter Interface Board – for the HP-PB I/O Board Slot (Auto Senses Between 10Mbps and 100Mbps)

Fiber channel adapter – 1063Mbps adapter installed in an HP T600-Class computer HSC slot – For linking to fiber channel mass storage only

HP-HSC Fast Wide SCSI-2 interface card with 2.0m (6.6ft) cable

16-channel RS-232C direct connect asynchronous multiplexer – Has RJ-45 connectors – For the HP-PB I/O board slot

16 channel RS-232C direct connect MUX board – Has RJ-45 connectors – For the HP-PB I/O board slot

32 Channel RS-232C Direct Connect MUX Board (with RJ-45 Connectors) – for the HP-PB I/O Board Slot (P/O J2096A)

32 Channel RS-232C Direct Connect MUX Board (with RJ-45 Connectors) – for the HP-PB I/O Board Slot

32 channel RS-232C direct connect MUX board – Has RJ-45 connectors – For the HP-PB I/O board slot

Token ring interface board – For the HP-PB I/O board slot

HP-HSC ATM/155Mbps adapter card

Switching power supply (Delta Electronics SMP-264AB REV. B) – 120/240VAC input, 50-60Hz – Three DC outputs, 260 watts – In HP-PB I/O card cage

Switching power supply (Delta Electronics SMP-264AB REV. B) – 120/240VAC input, 50-60Hz – Three DC outputs, 260 watts – In HP-PB I/O card cage

High voltage power supply (Astec AA50090) – 169-269VAC input, 350VDC nominal output, 6.3A, 2200 watts – With active power factor correction (PFC) and battery backup – Mounts in the right lower rear of the computer

DC-DC converter module (Yokogawa PS603) – 185-400VDC input – 24VDC output, 325 watts – Supply for the fan power

HP PA-RISC processor – 180MHz

HP PA-RISC processor upgrade kit – Includes one 180MHz PA-RISC processor with 8MB cache