Type | Image | Référence | Description | Cotation |
---|
KEYBOARD | | 435302-001 | PS/2 ‘Windows’ keyboard assembly (Silver and Carbonite Black) – Has attached 1.8M (6.0ft) cable with 6-pin (Violet) mini-DIN connector (USA) |
 |
CABLE | | 5182-4535 | Ribbon cable assembly – 3-pin (F) connector to 3-pin (F) connector – 30cm (11.8in) long – I2C bus cable assembly – From hot-swap backplane boards to system (mother) board (two used) |
 |
CABLE | | 5182-4523 | Fast Wide internal SCSI cable – 68-pin (M) to 68-pin (M) – 23cm (9in) long – Cable C4 – Between the two hot-swap backplane boards (configuration dependent) |
 |
CABLE | | 5182-4570 | Ribbon cable for one IDE hard disk drive – Cable marked ‘IDE hard disk cable’ – 40-pin (F) connector to 40-pin (F) connector – 40.9cm (16.1in) long |
 |
CABLE | | 5063-8400 | Ribbon cable with two self adhesive cable clamps and installation instructions – 8-pin (F) connector marked ‘NetServer’ to 8-pin (F) connector marked ‘Remote Assistant’ – 1.0m (39in) cable folded to be 63.5cm (25in) long – From Remote Assistant board to c |
 |
CABLE | | 5182-0015 | Floppy drive ribbon cable marked ‘Flexible disk cable’ – 34-pin (F) connector marked ‘to system board’ to a 34-pin (F) old-style edge connector and a 34-pin (F) new-style connector marked ‘to 3.5 inch flexible disk drive’ – 61.5cm (24.2in) long |
 |
CABLE | | 5182-4521 | Fast Wide SCSI ribbon cable (C2) – Cable marked ‘Int. SCSI cable C2-80 ohm’ – 68-pin (M) connector marked ‘System board or PCI board’ to 68-pin (M) connector marked ‘SCSI mass storage device’ – 59.9cm (23.6in) long – From hot-swap backplane boards to a PC |
 |
CABLE | | 5182-4522 | SCSI ribbon cable with termination – Cable is marked ‘Array SCSI cable (Narrow)’ – One 50-pin (F) connector marked ‘To array back plane’ and two 50-pin (F) connectors marked ‘To unterminated SCSI device’ – 34.3cm (13.5in) long – From CD-ROM drive to hot-s |
 |
CABLE | | 5182-6734 | Fast wide SCSI ribbon cable kit (C3)- Two connector mounting screws and a cable marked ‘Wide SCSI Channel B cable’ – 68-pin (M) connector to high density 68-pin (F) connector with latch clips for the rear panel – 47cm (18.5in) long – From system board SCS |
 |
CABLE | | D3330-60010 | NetServer LS cable kit – For adding drives or reconfiguring the system – Includes internal (C2) and external (C3) fast wide cables, and a narrow to fast wide adapter |
 |
BEZEL | | 5063-0328 | Bezel assembly – Plastic cover over the control panel PC board has cut outs for the switches and display |
 |
BEZEL | | 5063-5673 | ‘Hot swap’ bezel assembly – Frame around six ‘hot swap’ drives – Includes the hot swap drive retainer lock |
 |
FAN | | 3160-1004 | Tubeaxial fan with sensor (NMB Technologies 3610KL-04W-B49-P01) – 92mm x 92mm x 25mm thick, 12VDC, 2,850 RPM, 1.35CFM – Includes cable assembly – Mounts to the front panel (2 used) |
 |
ADAPTER | | 5182-4550 | SCSI adapter (68-pin (F) to 50-pin (M)) – Used in some configurations for the CD-ROM drive and/or another Single-Ended SCSI drive (Narrow 8-bit to Fast Wide 16-bit) |
 |
COVER | | 5063-0384 | Chassis cover – Includes front, top and both sides |
 |
COVER | | 5063-8301 | Locking cover – Attaches to the front of one of the ‘Hot swap’ drive trays |
 |
PANEL | | 5063-5676 | Filler panel (Dove Gray) – Covers the empty Hot-Swap drive slots |
 |
MODULE | | D3575-63002 | DC to DC converter module (5V to 3.3V) – Mounts above the power supply on the rear panel – For NetServers that have two processor boards with dual Pentiums only |
 |
MOUSE | | C3751-60201 | PS/2 two-button serial mouse (Quartz Gray) – Has attached 6ft cable with 6-pin mini-DIN connector – (Part of C3751B) |
 |
DRIVE | | D3581-69001 | 1.05GB hot-swap Fast SCSI-2 hard drive module (Parchment White) |
 |
DRIVE | | D4289-69001 | 9.1GB hot-swap Ultra SCSI-2 hard drive module (Quartz Gray) |
 |
DRIVE | | 5064-7985 | SCSI-2 CD-ROM drive (Flint Gray) – 32X CD-ROM read – Has loading tray – Replacement for the 4X CD-ROM (Model D2992B) and 12X CD-ROM drives |
 |
DRIVE | | D2035-60282 | 1.44MB, 3.5-inch floppy drive (Flint Gray) – 1/3 height – (Part of D2035A/B) |
 |
DRIVE | | D2076-69002 | 1GB Fast SCSI-2 hard drive – 3.5-inch form factor, low profile |
 |
DRIVE | | D2077-69001 | 2.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor |
 |
DRIVE | | D2967-69004 | HP LS NetServer Remote Assistant Assy (for Outside of Canada/US) (D2967C) – without on-board Modem – When Upgrading from a D2967A/B to D2967C also Order Firmware/Software Upgrade Kit |
 |
DRIVE | | D3340-69001 | 2.1GB SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor |
 |
DRIVE | | D3341-69001 | 4.0GB SCSI-2 hard drive – 5,400 RPM, 3.5-inch form factor |
 |
DRIVE | | D3582-69001 | 2.1GB hot-swap SCSI-2 hard drive module (Dove Gray) |
 |
DRIVE | | D3583-69001 | 4.2GB hot-swap SCSI-2 hard drive module (Parchment White) |
 |
MEMORY | | D2297-69001 | 16MB, 70nS, 36-bit parity SIMM memory module for HP LS NetServer |
 |
MEMORY | | D2974-63001 | 4MB, 70nS, 36-bit parity SIMM memory module for HP LS NetServer |
 |
MEMORY | | D3577-69001 | 8MB, 70nS, 36-bit parity SIMM memory module for HP LS NetServer |
 |
MEMORY | | D3578-69001 | 32MB, 70nS, 36-bit parity SIMM memory module for HP LS NetServer |
 |
PC BOARD | | D2968-69005 | HP LS NetServer Remote Assistant PC Board Assembly (Canada/US) (D2968C) – with on-board Modem – When Upgrading from a D2968A/B to D2968C also Order Firmware/Software Upgrade Kit |
 |
PC BOARD | | D2971-63006 | HP LS NetServer ECC Memory Board (with 12 SIMM Sockets) – Plugs into the Top of the System (Mother) Board (2 Can be Used) |
 |
PC BOARD | | D3330-69011 | HP LS NetServer System (Mother) Board – with VGA, IDE and 2 Fast Wide SCSI-2 Controllers – Large Vertical Board in Center of Computer |
 |
PC BOARD | | D3574-69001 | HP LS NetServer Processor Board (with Single 100MHz Pentium Processor IC) – Plugs into the System (Mother) Board (2 Can Be Used) |
 |
PC BOARD | | D3604-63003 | HP LS NetServer ‘Hot Swap’ Backplane Board – for the ‘Hot Swap’ Drives – Mounts in the Rear of the ‘Hot Swap’ Drive Cage (2 Used) |
 |
PC BOARD | | 5064-0739 | HP LS NetServer Control Panel Board (Includes the Display and Switches) – Mounts to the Front Panel |
 |
INTERFACE | | D2967C | Remote Assistant Board (for Outside of Canada/USA) – Intelligent EISA Based Remote Management Board with Onboard NiCad Battery and Processor – Does NOT Include a Modem |
 |
INTERFACE | | 27252-69001 | ISA 16-Bit LAN Interface Board with ThinLAN (10BASE-2) and AUI Connectors (27252A) |
 |
INTERFACE | | C3610-69050 | Dual Channel Fast Wide SCSI Disk Array Controller Board – (P/O C3610A) – Plugs into a PCI Board Slot on the System (Mother) Board |
 |
INTERFACE | | D2968C | Remote assistant board – Intelligent EISA based remote management board with onboard nickel cadmium (NiCd) battery, processor, and modem (Canada and USA) |
 |
INTERFACE | | J2585-69011 | 32-bit PCI LAN interface board – RJ-45 connectors – Supports both EtherTwist 10Base-T and 100VG/802.12 – (J2585B, part of J3009B, part of of J3010B) |
 |
INTERFACE | | J2585B | PCI 32-Bit LAN Interface Board – has RJ-45 Connector – Supports Both Ethertwist (10BASE-T) & 100VG/802.12 (J2585B, 1/6 of J3009B, 1/24 of J3010B) |
 |
INTERFACE | | J3239-61001 | ISA 16-Bit LAN Interface Board with EtherTwist (10Base-T) and AUI Connectors (Equivalent Replacement for 27247B, 1/6 of 27269B, 1/24 of J2427B) |
 |
POWER SUPPLY | | 5063-5635 | Power supply assembly – 470 watts – Mounts to the rear panel |
 |
PROCESSOR | | D3574A | HP NetServer Dual 5/100LS SMP processor board – For adding second processor board with one 100MHz Pentium processor |
 |
PROCESSOR | | D3575A | HP NetServer 5/100LS SMP processor board – For adding second processor board with two 100MHz Pentium processors |
 |