SCSI interface cable with thumbscrews on ends – 68 pin high density (M) to 68 pin high density (M) – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 128 ohms – 5.0m (16ft) long

Single-Ended SCSI-2 interface cable – 50-pin high density (M) thumbscrew to 50-pin low density (M) bail lock – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 10.0m (33ft) long

SCSI interface cable with thumbscrews on both ends – Has 68-pin high density (M) connectors – 20.0m (65.6ft) long – (C7532A)

Video cable with Enhanced Video Connectors (EVC) on both ends – 1.8m (6.0ft) long

Single-Ended SCSI-2 interface cable with bail locks on both ends – 50-pin low density (M) to 50-pin low density (M) – 1.0m (3.3ft) long –

Single-Ended SCSI-2 interface cable with bail locks on both ends – 50-pin low density (M) to 50-pin low density (M) – 0.5m (1.6ft) long

Single-Ended SCSI-2 interface cable with bail locks on both ends – 50-pin low density (M) to 50-pin low density (M) – 2.0m (6.6ft) long

Single-Ended SCSI-2 interface extension cable with bail locks on both ends – 50-pin low density (M) to 50-pin low density (F) – 1.0m (3.3ft) long – (92222D)

Single-Ended SCSI-2 interface cable with thumbscrews on both ends – 50-pin high density (M) to 50-pin high density (M) – 1.0m (3.3ft) long – (C2908A)

Single-ended SCSI-2 interface cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (M) – 0.5m (1.6ft) long

Single-Ended SCSI-2 interface cable with bail locks on both ends – 50-pin low density (M) to 50-pin low density (M) – 1.0m (3.3ft) long

Single-ended SCSI-2 interface cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (M) – 2.0m (6.6ft) long

Single-Ended SCSI-2 ribbon cable – Three 50-pin (F) internal connectors and a high density 50-pin (F) connector with latch clips for the rear panel – 75cm (29.5in) long – From system processor board to disk drive tray assembly

Wide Differential SCSI ribbon cable with a ferrite – Has three 68-pin (M) internal connectors and a 68-pin (F) connector for the rear panel – 94cm (37in) long – From optional Wide Differential SCSI-2 controller to disk drive tray assembly

Floppy ribbon cable – 26-pin (M) connector marked ‘This end to floppy’ to 26-pin (M) connector – 35.3cm (13.9in) long

Fan assembly and power cable – Provides the power and the cooling to the disk drive tray assembly – Neither the fan nor the power cable is available separately

CD audio cable – 3-pin (F) connector to 3-pin (F) connector – 23cm (9in) long – From system board to CD-ROM drive

Ultra Wide Single-Ended SCSI-2 cable with ferrite – Has three 68-pin (M) internal connectors and a high density 68-pin (F) connector for the rear panel – 93.7cm (36.9in) long

SCSI interface extension cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (F) – 5.0m (16ft) long

Single-ended SCSI-2 interface cable with thumbscrews on both ends – 50 pin high density (M) to 50 pin high density (M) – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 0.9m (3.0ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 1.0m (3.3ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 128 Ohms – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 10m (33ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 20.0m (66ft) long

Single-ended SCSI-2 interface cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (M) – 3.0m (9.8ft) long

Single-ended SCSI-2 interface cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (M) – 5.0m (16ft) long

Single-ended SCSI-2 interface cable with thumbscrews on both ends – 50 pin high density (M) to 50 pin high density (M) – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 50 pin high density (M) to 50 pin high density (M) – 1.5m (4.9ft) long

Single-ended SCSI-2 interface cable with thumbscrews on both ends – 50 pin high density (M) to 50 pin high density (M) – 2.0m (6.6ft) long

Single-ended SCSI-2 interface cable with thumbscrews on both ends – 50 pin high density (M) to 50 pin high density (M) – 5.0m (16ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 90 Ohms – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 128 Ohms – 0.5m (1.6ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 90 Ohms – 1.5m (4.9ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 1.5m (4.9ft) long

SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

Low Voltage Differential/Ultra2 Single-Ended SCSI interface cable with thumbscrews on both ends – 68-pin high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 10.0m (33ft) long

SCSI interface cable with thumbscrews on both ends – 68 pin high density (M) to 68 pin high density (M) – 128 Ohms – 10.0m (33ft) long

SCSI interface cable with thumbscrews on both ends – Has 68 pin high density (M) connectors – 20.0m (65.6ft) long

SCSI interface cable – Low Voltage Differential/Ultra2 Single-Ended SCSI cable with thumbscrews on both ends – 68-pin ultra high density (M) to 68-pin high density (M) – 2.5m (8.2ft) long

Single-Ended SCSI-2 interface cable – 50-pin high density (M) thumbscrew to 50-pin low density (M) bail lock – 1.0m (3.3ft) long

Single-ended SCSI-2 interface cable – 50 pin high density (M) thumbscrew to 50 pin low density (M) bail lock – 1.5m (4.9ft) long

Single-Ended SCSI-2 interface cable – 50-pin high density (M) thumbscrew to 50-pin low density (M) bail lock – 1.5m (4.9ft) long – (K2297)

Chassis assembly – Includes all covers, disk filler panels, main tray, storage tray, hard drive trays, floppy tray, fans, speaker, light pipe, rear panel assembly (with handle)

Fan assembly and power cable – Provides the power and the cooling to the disk drive tray assembly – Neither the fan nor the power cable is available separately

Tubeaxial fan – 90mm x 90mm – Mounts in the fan shroud at the rear of the main tray assembly (Two used)

VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics – Includes color recovery – Has EVC video output connector

VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics – Includes color recovery – Has EVC video output connector

Dual VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics – Includes color recovery – Has EVC video output connector

Dual VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics; includes color recovery – Has EVC video output connector

HP VISUALIZE-fx2 graphic accelerator board – 24/8 bit accelerated 3D solids – Has EVC video connector – Requires HP-UX 10.20 with ‘Additional Core Enhancements’ (ACE)

VISUALIZE-FX2 graphic accelerator board – 24/8 bit accelerated 3D solids – Has EVC video connector – Requires HP-UX 10.20 with ‘Additional Core Enhancements’ (ACE)

VISUALIZE-FX4 graphic accelerator board – 24+24/8 bit performance 3D solids – Has EVC video connector – Requires HP-UX 10.20 with ‘Additional Core Enhancements’ (ACE)

VISUALIZE-FX4 graphic accelerator board – 24+24/8 bit performance 3D solids – Has EVC video connector – Requires HP-UX 10.20 with Additional Core Enhancements (ACE)

Video output board for VISUALIZE-FX series graphics products only – Provides NTSC, PAL,AND S-VIDEO outputs

Texture memory upgrade for VISUALIZE-FX4 – Adds 16MB texture memory and 32KB x 32KB virtual texture cache

Texture memory upgrade for VISUALIZE-FX4 – Adds 16MB texture memory and 32KB x 32KB virtual texture cache

Enhanced Video Connector (EVC) video adapter cable – EVC (M) to 15-pin (F), 20cm (7.87in) long – Used to connect EVC video output to 15-pin monitor connector

Enhanced Video Connector (EVC) video adapter cable – EVC (F) to 15-pin (M) – 7.87in (0.2m) long – Used to connect EVC video output to 15-pin monitor connector – (A4167A)

Enhanced Video Connector (EVC) video adapter cable – EVC (F) to 15-pin (M), 20cm (7.87in) long – Used to connect EVC video output to 15-pin monitor connector

Enhanced Video Connector (EVC) video adapter cable – EVC (M) to 15 pin (F), 20cm (7.87in) long – Used to connect EVC video output to a 15-pin monitor connector

Empty I/O slot cover – For empty rear panel EISA, GSC, and PCI board slots

Filler panel – For empty 3.5-inch drive bays

Filler panel – For empty 5.25-inch drive bays

1.42/1.44MB 3.5in high-density disks (Unformatted) (10/BOX)

2GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor – (Part of A4213A)

2.0GB Differential Fast Wide SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor

4.0GB Fast Wide Differential SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor – (Part of A4477A)

4GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor

2.0GB Ultra Wide Single-Ended SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high – (Part of A4568A, A4571A)

4.0GB Ultra Wide Single-Ended SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high – (Part of A4569A, A4572A)

9.1GB Ultra Wide Single-Ended SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.6-inch high – (Part of A4570A, A4573A)

2.0GB Fast Wide Differential SCSI-2 hard disk drive – 3.5-inch form factor, low profile

4GB Single Ended SCSI-2 hard drive – 3.5-inch form factor

1.44MB slim line floppy drive

2GB/4GB Single-Ended SCSI-2 DDS-1 (DAT) tape drive

4.0GB Differential Fast Wide SCSI-2 hard drive – 3.5-inch form factor

Single-Ended SCSI-2 CD-ROM drive – 4X CD-ROM read

1.44MB slim line floppy drive

2GB Differential Fast Wide SCSI-2 hard drive – 3.5-inch form factor

9.1GB Differential Fast Wide SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor

4.0GB Fast Wide Differential SCSI-2 hard drive – 7,200 RPM, 3.5-inch form factor

4GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor

2.0GB Ultra Wide Single-Ended SCSI hard disk drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high

4.0GB Ultra Wide Single-Ended SCSI hard drive – 7,200 RPM, 3.5-inch form factor, 1.0-inch high

9.1GB Ultra Wide Single-Ended SCSI hard disk drive – 7,200 RPM, 3.5-inch form factor, 1.6-inch high

2GB Single-Ended SCSI-2 hard drive – 3.5-inch form factor

Single-Ended SCSI-2 CD-ROM drive – 12X CD-ROM read

4GB/8GB Single-Ended SCSI-2 DDS-2 DAT tape drive

2GB/4GB Single-Ended SCSI-2 DDS-1 (DAT) tape drive – (A4076A)

4GB/8GB Single-Ended SCSI-2 DDS-2 (DAT) tape drive – 5.25-inch form factor

Single-Ended SCSI-2 slot load DVD-ROM drive kit – 6X DVD-ROM read, 32X CD-ROM read – Includes drive with headphone jack & volume control, instruction sheet, and CD audio cable – (Pioneer DVD-303/304 mechanism)

64MB, 50ns, 72-pin EDO DIMM memory module for HP9000 B180L

128MB, 50ns, 72-pin EDO DIMM memory module for HP9000 B180L

512kB, 100MHz cache memory module – Plugs Into one of two sockets on the system processor board (2 used)

2MB VISUALIZE-EG display memory RAM daughter board

2MB VISUALIZE-EG display memory RAM daughter board

64MB EDO SIMM memory upgrade kit – Includes two 32MB, 50nS, ECC EDO SIMM modules

64MB EDO SIMM memory upgrade kit – Includes two 32MB, 50nS, ECC EDO SIMM modules

128MB EDO memory upgrade kit – Includes two 64MB, 50nS ECC EDO SIMM modules

128MB EDO SIMM memory upgrade kit – Includes two 64MB, 50nS ECC EDO SIMM modules

256MB EDO memory upgrade kit – Includes two 128MB, 50nS ECC EDO SIMM modules

256MB EDO SIMM memory upgrade kit – Includes two 128MB, 50nS ECC EDO SIMM modules

HP9000 B180L EISA/GSC/PCI Backplane Board (A4542A) – Mounts in Center of Main Tray Assembly – 5 Volt 32 Bit PCI

HP9000 B180L System processor board – 180MHz – System Processor Board

HP9000 B180L Z-Buffer Accelerator Board (A4242A, 1 of 2 Boards in A4079B, 1 of 2 Boards in A4441A, 1 of 2 Boards in A4442A) – For HyperCRX-8 (A4070B) or HyperCRX-24 (A4071B) Graphics Boards

HP9000 B180L VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics – Includes color recovery – (Part of A4450A)

HP9000 B180L Dual VISUALIZE-EG graphic accelerator board – For 2D and 3D wireframe graphics – Includes color recovery – (A4451A)

HP9000 B180L 2MB EG Display Memory RAM Daughter Board (A4452A) – Mounts on the A4450A/A4451A Optional VISUALIZE-EG Graphics Board

HP9000 B180L VISUALIZE-FX2 graphics board – 1280 × 1024 accelerated 3D solids double-buffered 12-plane color graphics board with 8 overlay planes – (Part of A4552A)

HP9000 B180L VISUALIZE-FX4 graphics board – 1280 × 1024 accelerated 3D solids double-buffered 24-plane color graphics board with 8 overlay planes

HP9000 B180L 16MB texture memory and 32KB x 32KB virtual texture cache – For A4553A/B (VISUALIZE-FX4) graphics board – Adds 8 planes

EISA HP-IB Host Adapter Board (25560A)

EISA HP-IB Interface – Occupies EISA Slot in Computer

EISA PSI board – Provides SNA/X.25 LAN connection – High Speed EISA X.25 Board (P/O J2794A)

Single-ended SCSI-2 interface extension cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (F) – 1.0m (3.3ft) long

Fast Single-Ended SCSI-2 EISA host bus adapter board – Single Ended SCSI-2 Interface Board – Plugs into an EISA Bus Slot (A2679A)

Fast Wide Differential SCSI-2 GSC/HSC interface board – (Part of A4107A)

Wide Differential SCSI-2 Interface Board – Attaches to Side of Backplane Board

Remarketed Wide Differential SCSI-2 Interface Board – Attaches to Side of Backplane Board

Wide Differential SCSI-2 Interface Board – Attaches to Side of Backplane Board (A2889A)

SCSI interface extension cable with bail locks on both ends – 50 pin low density (M) to 50 pin low density (F) – 3.0m (9.8ft) long

Token Ring (IEEE 802.5 network) interface board – Plugs into an EISA bus slot – (Part of J2165A)

Token ring (IEEE 802.5 networks) interface board – Plugs into an EISA bus slot

ISDN BRI link module for HP 9000 series 700 – External box which connects to the computer via a single ended SCSI-2 interface cable and to the ISDN network via an RJ-45 cable – Includes software, power moudle, power cord, SCSI terminator, and RJ-45 cable

8 Port RS-232 Direct Connect MUX System Board (P/O J2482A) – Plugs into an EISA Bus Slot

8 port RS-232 direct connect MUX system board – Plugs into an EISA bus slot

High speed X.25 board – Provides line speed up to 1.5 Mbps – Plugs into an EISA bus slot

Switching power supply (Delta DPS-200QP) – 115-230VAC input, 50-60Hz – Five DC outputs, 200 watts – Mounts in the bottom of the left side of the main tray assembly